|
|
tlee
New User
Nov 16, 2013, 3:41 PM
Post #1 of 8
(1716 views)
|
|
73 ford no brakes
|
Sign In
|
|
Hi. I have a 1973 ford f100 pickup with a 302 and fmx automatic. I pulled this truck out of a field after it had sat over a decade. I got the truck to run but has absoluteluy no brakes. will not build up pressure. I replaced the master cylinder and still nothing. cracked bleeder valve on caliper and its dry. any help with this would be appreciated. thanks
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Nov 16, 2013, 4:17 PM
Post #2 of 8
(1709 views)
|
|
Re: 73 ford no brakes
|
Sign In
|
|
Is it losing the fluid or you just can't get it to flow to the wheels?
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
tlee
New User
Nov 16, 2013, 4:22 PM
Post #3 of 8
(1702 views)
|
|
Re: 73 ford no brakes
|
Sign In
|
|
no flow to wheels. the fluid in the resovoir isn't going down. if it is its not enough to notice
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Nov 16, 2013, 4:24 PM
Post #4 of 8
(1698 views)
|
|
Re: 73 ford no brakes
|
Sign In
|
|
Did you bleed the master before putting it on?
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
tlee
New User
Nov 16, 2013, 4:25 PM
Post #5 of 8
(1696 views)
|
|
Re: 73 ford no brakes
|
Sign In
|
|
no. did not know I was supposed to. how would I do that?
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Nov 16, 2013, 4:30 PM
Post #6 of 8
(1694 views)
|
|
Re: 73 ford no brakes
|
Sign In
|
|
Yes, that makes bleeding easier. Crack open the lines at the master until fluid starts draining and then re-tighten them. I would then completely remove the bleeders from the front wheels and let it gravity bleed. Make sure you keep the master full. The bleeders themselves could be plugged up. If they are you can use a small drill bit to dig the crud out of them. You may end up needing a pressure bleeder.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
(This post was edited by Hammer Time on Nov 16, 2013, 4:31 PM)
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Nov 17, 2013, 12:01 AM
Post #7 of 8
(1679 views)
|
|
Re: 73 ford no brakes
|
Sign In
|
|
As HT said get the master to work right at it. If it means taking it off and "bench bleeding" that do it.
Anyone correct me if wrong but I think there's a likely red rubber button or just the button without the rubber cover on the proportioning valve that may have to be pushed down to center it or fluid wont flow to either the front or rears. I think the idea was to give a better % of braking with a failure of either front or rear system. Those should self center to a "home" position but might not now.
If all is centered and air out of master these should plain gravity bleed out. Sitting that long brings out plenty of possible snags,
T
|
|
| |
|
|
tlee
New User
Nov 17, 2013, 4:32 AM
Post #8 of 8
(1673 views)
|
|
Re: 73 ford no brakes
|
Sign In
|
|
thanks weather permitting ill get to trying all of that when its daylight.
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
Lukewarm Heat............
Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086
1989 toyota pickup 3.0 crank no start
