|
|
Car will not start after stereo installation
|
|
|
| |
|
lucas19562
User
Sep 3, 2020, 10:27 AM
Post #1 of 18
(1494 views)
|
Car will not start after stereo installation
|
|
|
Hello, I have a: 2013 Chrysler 200 2.4 L engine with 99,660 miles Recently I installed a stereo, before you ask I did not unhook battery prior. but during course of install I did make a mistake and cut an incorrect wiring group that went to my hazard lights, the stabilizer control(car swerving looking thing). Other than that my install went fine and everything electrical seems top come up fine and stereo does work. The only issue i have is not my engine will not even attempt to start up when prompted. I've gone through trying to troubleshoot the anti-theft, since that seems the most common issue, and nothing has worked. I tried applying power directly to my starter to try to turn on engine and nothing happens. My battery seems to be in good condition, won't respond to being jumped or being charged so seems to have full power. The only other kind of hint I have is both my check engine and battery light are on and stay on, they do not blink. The car swerving light is also on, but i just thought that had to do with my accidentally cutting that wire.
|
|
| |
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 3, 2020, 11:55 AM
Post #2 of 18
(1486 views)
|
Re: Car will not start after stereo installation
|
|
|
So you just cut up unknown wires in a computer controlled car and you expect someone on the Internet to be able to tell you what you did? We have no idea what you did. I suggest you just go back over what you did and then test every fuse in the car with a test light. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
lucas19562
User
Sep 3, 2020, 12:06 PM
Post #3 of 18
(1482 views)
|
Re: Car will not start after stereo installation
|
|
|
I followed a wiring diagram that displayed the wires from after market radio and chrysler radio wiring.
|
|
| |
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 3, 2020, 12:09 PM
Post #4 of 18
(1478 views)
|
Re: Car will not start after stereo installation
|
|
|
Why didn't you just buy a "plug and play" adapter plug instead of cutting wires? ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
lucas19562
User
Sep 3, 2020, 12:13 PM
Post #5 of 18
(1473 views)
|
Re: Car will not start after stereo installation
|
|
|
Yea I looked online for something like that so I wasnt sure if one existed, which is stupid i know but yea. I cant go back on it now. I'm just looking for any possible ideas. I don't need any exact solutions or anything just something to potentially point me in right direction. I've checked fuses and relays and all seem good. No fuses blown and only relays I have are for radiator.
|
|
| |
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 3, 2020, 12:19 PM
Post #6 of 18
(1459 views)
|
Re: Car will not start after stereo installation
|
|
|
If you are sure you put all the wires back the way they were, then you have to have burned out a fuse, fusible link or module. It may require a professional level scan tool to find out if all modules are communicating. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
lucas19562
User
Sep 3, 2020, 12:26 PM
Post #7 of 18
(1457 views)
|
Re: Car will not start after stereo installation
|
|
|
AFTERMARKET RADIO PYLE Radio Disc Wire Tag Wire Colour RR speaker + RR+ Purple RR speaker - RR- Purple/Blk RL speaker + RL+ Green RL speaker - RL- Green/Blk FR speaker + FR+ Grey FR speaker - FR- Grey/Blk FL speaker + FL+ White FL speaker - FL- White/Blk SW Key KEY1 Green/Wht Amp Control AMPCON Blue/Wht Illumi ILL Orange Ground GND Black GND Black Acc ACC+ Red Power B+ B+ Yellow Back BACK Brown Parking PARKING Pink Ant Cont AUTOANT Blue SW Key KEY2 Grey/Wht Backup Camera CAMVIDIN Co-ax - Blk FACTORY WIRING/RADIO 2013 Chrysler 200 Disc Wire Colour Pin/Location Right Rear Speaker Wire (+) Positive: DG/B Pin 10 Right Rear Speaker Wire (-) Negative: Y/G Pin 11 Left Rear Speaker Wire (+) Positive: DG/Tan Pin 8 Left Rear Speaker Wire (-) Negative DG/Gray Pin 9 Right Front Speaker Wire (+) Positive DG/P Pin 19 Right Front Speaker Wire (-) Negative DG/Y Pin 20 Left Front Speaker Wire (+) Positive G/P Pin 21 Left Front Speaker Wire (-) Negative G/Y Pin 22 Car Radio Amp Turn On Wire N/A N/A Car Radio Illumination Wire White/Purple (Parking Lights)@Driver kick Car Stereo Ground Wire: Black Pin 12 Car Radio Ignition Switched Wire @ Cigarette Lighter or Interface Car Radio Constant 12v+ Wire Red/Brown Pin 1 Car Stereo Reverse Wire + White/Green (+) @ Light Car Stereo Power Antenna: Gray/Orange Pin 7
|
|
| |
|
lucas19562
User
Sep 3, 2020, 12:28 PM
Post #8 of 18
(1455 views)
|
Re: Car will not start after stereo installation
|
|
|
I added the wiring diagram just so you can get an idea of the wiring. I didn't consider the other 2 things beside fuse. I'll check fuses again and finally be able to convince my fiance that it is out of my hands and actually get some help......lol
|
|
| |
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 3, 2020, 12:42 PM
Post #9 of 18
(1448 views)
|
Re: Car will not start after stereo installation
|
|
|
Does your car have a factory standalone amp? ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
(This post was edited by Hammer Time on Sep 3, 2020, 12:42 PM)
|
|
| |
|
lucas19562
User
Sep 3, 2020, 1:52 PM
Post #10 of 18
(1417 views)
|
Re: Car will not start after stereo installation
|
|
|
Yes, I believe so. Would that affect my cars ability to start?
|
|
| |
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 3, 2020, 1:59 PM
Post #11 of 18
(1414 views)
|
Re: Car will not start after stereo installation
|
|
|
No, but is sure would make your wiring diagram wrong. There are 2 stereo systems available and it appears you have the premium system. Here is the actual wiring diagram for that model. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
lucas19562
User
Sep 3, 2020, 2:08 PM
Post #12 of 18
(1408 views)
|
Re: Car will not start after stereo installation
|
|
|
I don't want to be asking too much but wherever you find that does it also explain how to set up to the aftermarket wiring? The aftermarket wiring on the diagram i had was correctly portrayed....
|
|
| |
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 3, 2020, 2:15 PM
Post #13 of 18
(1401 views)
|
Re: Car will not start after stereo installation
|
|
|
That is a factory wiring diagram for that vehicle. Anything to do with aftermarket stuff would come from the aftermarket manufacturer. The info you have for the aftermarket radio should be correct. What is wrong are the color codes and locations of the car side of those instructions. They gave you instructions for the base model radio. If you notice on my diagram most of the wires you are looking for aren't even at the radio, they are at the amplifier, wherever that is. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
lucas19562
User
Sep 3, 2020, 2:38 PM
Post #14 of 18
(1390 views)
|
Re: Car will not start after stereo installation
|
|
|
I believe i may try to take it in somewhere this seems like more work than I'd be able to perform. I've looked at the dia this whole time and can't quite wrap my head around it
|
|
| |
|
lucas19562
User
Sep 3, 2020, 2:42 PM
Post #15 of 18
(1386 views)
|
Re: Car will not start after stereo installation
|
|
|
If i buy a new original wiring harness and reinstall my factory radio, do you think that should solve at least a majority of my issues? Like just returning everything back to base
|
|
| |
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 3, 2020, 2:52 PM
Post #16 of 18
(1371 views)
|
Re: Car will not start after stereo installation
|
|
|
It might. It depends on if the problem is just something wired wrong or if the incorrect wiring has done damage to something. The wiring at least needs to be verified that it is wired correctly before going any further. You need to be absolutely sure which system you have to know if it is wired correctly. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
lucas19562
User
Sep 3, 2020, 3:51 PM
Post #17 of 18
(1355 views)
|
Re: Car will not start after stereo installation
|
|
|
Got it, rechecked fuses and the one for the computer and it was blown. Thanks for your help I feel like an idiot, don't know how I missed it.
|
|
| |
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 3, 2020, 3:55 PM
Post #18 of 18
(1353 views)
|
Re: Car will not start after stereo installation
|
|
|
LOL. well at least you found it. Closing this now as solved ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|