Interio lights and bell - Automotive Wiring and Electrical


	Auto Repair Home	SEARCH POSTS	WHO'S ONLINE	LOG IN

Automotive Repair

Car Troubleshooting Topics
  Car Troubleshooting
  Engine Troubleshooting
  Engine Fault Codes
  Electrical and Wiring
  Transmission Problems

Car Repair Topics
  Car Making Noises
  Car Stereo Repair
  Heating or AC Issues
  Motorcycles and ATVs
  Tricks of the Trade
  Truck Repair Advice

Site Options:
  Login
  Sign up here!

Latest Forum Post

1989 toyota pickup 3.0 crank no start

I have a 1989 toyota pickup 3.0 crank no...

Strut spring orientation and strut mount tension nut

2017 Nissan rogue awd 2.5 L Put in Monro...

Transmission stuck in part, I have tried everything

So I'm working on my elderly fathers 201...

2017 dodge journey LED headlights on/off randomly

Year of vehicle 2017 Make of vehicle dod...

Kia Soul starter replacement issues!

Okay so my car is a 2010 Kia soul 2.0 en...

Please Help - Knock sound & engine fail

Hi all, Hoping to get some insight and ...

multiple warning lights

2013 GMC Terrain 130,000 miles 4 cylinde...

03 alero no low speed blower

Good day everyone, I have a 2003 Olds a...

04 Chevy 2500hd tail light issues

Help!!! I have changed my combo switch...

1999 Grand Caravan Sport not starting.

Hi. I'm new here. I hope someone can hel...

Interio lights and bell

Sign up here!

Search for (search options)

Auto Repair Home>> Automotive Repair>> Automotive Wiring and Electrical

TXDave
Novice

Nov 20, 2005, 9:39 AM

Post #1 of 4 (1679 views)

Interio lights and bell	Sign In

I have a 1995 Plymouth Grand Voyager. On my rough road it has begun to flash the interior light and bell (door adjar lite does not come on. On smooth roads stopping fast does same thing. Where is the loose wire? Thanks.

DanD
Veteran / Moderator
DanD profile image

Nov 20, 2005, 10:34 AM

Post #2 of 4 (1677 views)

Re: Interio lights and bell	Sign In

It could be anywhere from the rear hatch pin switch to one of the door pin switches, (that’s if this van still has pin switches) to a wire that has rubbed through and a bump puts the wire to ground, turning on the lights. There is a maze of wires to each door.
You may need to go to each door switch, whether it’s a pin switch style (in the crotch of the door, looks like a push button) or one that is incorporated in the latch mechanism and isolate it from the others.
Doing one door at a time and leaving it disconnected, until you find out which is at fault, if all doors are disconnected and the problem is still there, now you’re into a bit of a search as to where the short to ground is in the wiring harness.
Good luck, because if the light were on all the time it would be relatively easy to find the short but having to drive down a bumpy road to have it do its thing is going to be a bit of a challenge.
Dan.

Canadian "EH"

Tom Greenleaf
Ultimate Carjunky / Moderator
Tom Greenleaf profile image

Nov 20, 2005, 11:06 AM

Post #3 of 4 (1674 views)

Re: Interio lights and bell	Sign In

I had one of those and it was the sliding door switch. I just stacked a couple pennies up with glue to push the button a bit more and it stayed fine for years. Hope it's something that simple, - T

TXDave
Novice

Dec 5, 2005, 8:20 AM

Post #4 of 4 (1652 views)

Re: Interio lights and bell	Sign In

Thanks for the help (couldn't find a feedback section). I removed the door panels checked everywhere. Tried pennies. I removed and re-installed all pin switches except side door. This action seems to have re-grounded the system and I only get a "ding" occationally. Thanks for the help. TXDave

Search for (options) Privacy Sitemap