|
|
aipjian
User
Mar 16, 2012, 9:55 AM
Post #1 of 24
(17456 views)
|
|
P0133 hyundai elantra
|
Sign In
|
|
Check engine light on went into emissions and failed (forgot code but needed new 02 sensor) got 02 new 02 sensor. Mechanic cleared code but came back on and now I have code P0133 and check engine light is on.
Failed emission again - multiple not ready.
I pulled the computer fuse and kept it out for about 30 minutes & than put it back in place. Check engine light has not come back on and it's been a week.
Will I pass emission now?
|
|
| |
|
| | |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Mar 16, 2012, 1:10 PM
Post #4 of 24
(17394 views)
|
|
Re: P0133 hyundai elantra
|
Sign In
|
|
If you have been driving it around for a week since clearing the codes, most if not all of the monitors should be ready. Every time you clear codes you reset monitors and the OBD2 software has to go through a drive cycle till the software can run tests on the systems.
There is no way for us to know if your going to pass emissions because we can't hook up our scan tools or 5 gas analyzers through the computer screen to test your car.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Mar 16, 2012, 1:11 PM)
|
|
| |
|
|
aipjian
User
Mar 16, 2012, 2:26 PM
Post #5 of 24
(17363 views)
|
|
Re: P0133 hyundai elantra
|
Sign In
|
|
If someone were able to tell me what is wrong with it, I would get it fixed, but no one has been able to tell me what's wrong.
So I guess, what I'm asking is... is it possible that by removing the fuse and rebooting the computer, I fixed the problem.
|
|
| |
|
|
nickwarner
Veteran
/ Moderator
Mar 16, 2012, 2:55 PM
Post #7 of 24
(17349 views)
|
|
Re: P0133 hyundai elantra
|
Sign In
|
|
We could possible be pointing you in the right direction if you got a code number for us instead of erasing your adaptives. How did you know the O2 sensor needed to be replaced? Did you test it or did some saleman at an Autozone scan your codes and tell you what you needed to buy from him?
|
|
| |
|
|
aipjian
User
Mar 16, 2012, 3:35 PM
Post #8 of 24
(17334 views)
|
|
Re: P0133 hyundai elantra
|
Sign In
|
|
First code was P0132 - put in new 02 sensor, Mechanic cleared code - light came back on with in 24 hrs... this time P0133.
Swapped out with another 02 sensor, Mechanic cleared code. same issue... 24 hrs later P0133.
Took out the fuse and it has been a week of no check engine light.
Is there a difference between him clearing code and me removing fuse?
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Mar 16, 2012, 3:38 PM
Post #9 of 24
(17333 views)
|
|
Re: P0133 hyundai elantra
|
Sign In
|
|
Year and engine size?
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
|
aipjian
User
Mar 16, 2012, 3:43 PM
Post #10 of 24
(17328 views)
|
|
Re: P0133 hyundai elantra
|
Sign In
|
|
2003 Elantra / DOCH 16V
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Mar 16, 2012, 4:08 PM
Post #11 of 24
(17315 views)
|
|
Re: P0133 hyundai elantra
|
Sign In
|
|
It's possible that when you disconnected the battery you solved a ground problem. There may have been excessive resistance in the connection at the battery. One of the steps in the trouble chart for the P0133 is to check for excessive resistance in the ground circuit at the battery. You may want to clean your battery terminals really good to make sure the problem doesn't reoccur from that.
It may be a good idea to hook up a memory maintainer, which is nothing more than another battery connected to the electrical system, to keep the memory alive in the PCM if you go to remove your terminals to clean them. That way you don't have to go through the chore of doing the drive cycle to ready all the monitors again.
Once you know the terminals are clean and tight. Find someone with a scanner that can show you the system status of the monitors. If all the monitors show ready, then use the scanner to check for pending trouble codes. Pending trouble codes won't turn on the check engine light, but can later if the test that failed that signals the code fails again.
If it all checks out good, then its possible you end up passing your emissions test.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Mar 16, 2012, 4:10 PM)
|
|
| |
|
|
aipjian
User
Mar 16, 2012, 4:22 PM
Post #12 of 24
(17303 views)
|
|
Re: P0133 hyundai elantra
|
Sign In
|
|
I forgot to mentions, the same day I removed the fuse, I also cleaned to battery acid from the termanials.
What type of scanner do I need to see the systems are ready, is that something I can get done at Auto Zone? I know very little about this stuff...
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Mar 16, 2012, 4:38 PM
Post #13 of 24
(17296 views)
|
|
Re: P0133 hyundai elantra
|
Sign In
|
|
I'm not sure if Autozone sells a scanner that intrusive, but you could check if your interested. It's not a code reader, but an actual scanner that can read live data, retrieve current and pending codes, clear codes, look at readiness monitors status, etc.
For example this actron scanner can view monitor status. If they show OK, COMPLETE or NA (not available) then your good to go. If you have any that show INC (incomplete) that means the drive cycle for the monitor hasn't been performed or there is a problem, which usually sets a pending or current code, keeping the incomplete monitor from running. Incomplete monitors fail your emissions test right on the spot.
Once a monitor is ready that means the criteria has been met, so the OBD2 software can test the system of that monitor. The software may conduct numerous non continuous tests depending on the system. All the test results are stored in mode$06, but that is something you really don't need to be concerned about unless you plan on learning Hex codes and the nuts and bolts of OBD2.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Mar 16, 2012, 4:48 PM)
|
|
| |
|
|
comnavguy
User
Mar 18, 2012, 1:37 AM
Post #14 of 24
(17250 views)
|
|
Re: P0133 hyundai elantra
|
Sign In
|
|
If you google drive cycle for your car, you'll get an idea of what you need to do to get all your I/M monitors "ready". On some vehicles, you can have one or two "not ready" flags and the inspection will proceed. Best though to get someone with a scanner to tell you if all the I/Ms are ready.
|
|
| |
|
|
aipjian
User
Mar 18, 2012, 7:53 AM
Post #15 of 24
(17235 views)
|
|
Re: P0133 hyundai elantra
|
Sign In
|
|
I went to Auto Zones today and they could not find any codes, they also said they found five "ready's"
How many ready's do I need?
|
|
| |
|
|
aipjian
User
Mar 19, 2012, 12:41 PM
Post #16 of 24
(17204 views)
|
Re: P0133 hyundai elantra
|
Sign In
|
|
It's been a week and I still have 2 "not ready" Evaporative control system and oxygen senson.
Any Ideas, I have to weeks left to pass emssions.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Mar 19, 2012, 1:13 PM
Post #17 of 24
(17198 views)
|
|
Re: P0133 hyundai elantra
|
Sign In
|
|
Drive Schedule Notes:
- Coolant needs to be within 0 to 40 C (0 to 104 F) at start.
- Fuel level must be above 15% .
- When decelerating from 50-55mph there needs to be at least 5 seconds of fuel cut-off; its best to close throttle as soon as possible for 5 seconds to assure decel fuel cutoff occurs.
- Try to maintain constant throttle as much as possible during the steady state speed portions of the drive cycle.
Cautions :
- This schedule is best driven on a dyno if available, otherwise find the best road with least traffic
- Obey speed limits and drive safely.
- If you lose the schedule due to traffic, attempt to get back to it when conditions are safe to do so.
- Keep your eye on the road and avoid looking at the schedule constantly; its best to have a passenger describe the schedule to you while driving.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Mar 19, 2012, 5:55 PM
Post #18 of 24
(17180 views)
|
|
Re: P0133 hyundai elantra
|
Sign In
|
|
Which oxygen sensor monitor? There are two of them. One is for testing the O2 sensor heater and the other tests the performance of the O2 switch signal. EVAP monitor is the most difficult one to complete.
Looks like someone is going to have to use an enhanced scanner to look at mode $06 test results to see what is hanging up the O2 monitor which definitely should had run by now.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Mar 19, 2012, 5:55 PM)
|
|
| |
|
|
aipjian
User
Mar 20, 2012, 7:04 AM
Post #19 of 24
(17153 views)
|
|
Re: P0133 hyundai elantra
|
Sign In
|
|
It's not the heated sensor, it's the other one. Could it be that I need to tighten it? I only had a hand socket tool at the time, but I can use my breaker bar if needed.
Thank you,
Allen
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Mar 20, 2012, 5:11 PM
Post #20 of 24
(17127 views)
|
|
Re: P0133 hyundai elantra
|
Sign In
|
|
O2 sensors don't need to be that tight. ...around 25 ft lbs is enough.
If that monitor doesn't ready, your going to have to get it checked out. What is odd is that the catalyst monitor passed. Usually the catalyst monitor won't run unless the O2 sensor monitor has passed.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Mar 20, 2012, 5:14 PM)
|
|
| |
|
|
aipjian
User
Mar 21, 2012, 3:19 PM
Post #21 of 24
(17104 views)
|
|
Re: P0133 hyundai elantra
|
Sign In
|
|
6 / 7 sensors ready!!!! I will go the test tomorrow, I can have 1 not ready in IL.
Is it possible that any of them can go back to not ready???
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Mar 21, 2012, 3:46 PM
Post #22 of 24
(17099 views)
|
|
Re: P0133 hyundai elantra
|
Sign In
|
|
As long as you don't do a clear codes function with a scan tool or disconnect the battery, the monitors won't reset. Good luck with your testing.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
|
aipjian
User
Mar 22, 2012, 1:03 PM
Post #23 of 24
(17062 views)
|
|
Re: P0133 hyundai elantra
|
Sign In
|
|
I passed, with 8 days to spare. Thank you all for your help!
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Mar 22, 2012, 2:01 PM
Post #24 of 24
(17055 views)
|
|
Re: P0133 hyundai elantra
|
Sign In
|
|
I'm sure I speak for all regulars here no doubt. Thanks for sharing a success story and hope we as a site of individuals were of some help,
Tom Greenleaf
(This post was edited by Tom Greenleaf on Mar 22, 2012, 2:41 PM)
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
1989 toyota pickup 3.0 crank no start
Please Help - Knock sound & engine fail
