P0496 High purge Flow ....help - Engine ODB2 Fault Codes


	Auto Repair Home	SEARCH POSTS	WHO'S ONLINE	LOG IN

Automotive Repair

Car Troubleshooting Topics
  Car Troubleshooting
  Engine Troubleshooting
  Engine Fault Codes
  Electrical and Wiring
  Transmission Problems

Car Repair Topics
  Car Making Noises
  Car Stereo Repair
  Heating or AC Issues
  Motorcycles and ATVs
  Tricks of the Trade
  Truck Repair Advice

Site Options:
  Login
  Sign up here!

Latest Forum Post

2011 Dodge Nitro OBD scanner seems to drain battery in 10-20 minutes

When I bought this car in summer 2023, a...

Grounding Cable, 2017 Jeep Renegade Trailhawk

The Cable that connects my negative batt...

Rough Idle (Found new thing)

Hi everyone. First of all sorry for bad ...

equipment

hey yall. im a first year engineering st...

HELP

I have a 1956 1/2 ton panel truck, 69 35...

Howdy

    Just wanted to s...

ABS/Tractiob/Brake Lights on But No DTCs

Hello all, Recently while driving m...

Chevy strut replacement

I'm trying to get a sensor of some kind ...

2020 suburban new transmission and issues after install

recently had the transmission fail at 11...

Caliper piston post cleaning won't screw in

Hello, 2013 Hyundai Elantra limited (ma...

P0496 High purge Flow ....help

Sign up here!

Email This Post

Auto Repair Home>> Automotive Repair>> Engine ODB2 Fault Codes

LuckyDogLD
New User

Jan 27, 2015, 2:35 PM

Post #1 of 3 (1976 views)

P0496 High purge Flow ....help	Sign In

Hello all and thanks for taking your time to look at my post.

I have a 2008 Chevy Cobalt 2.2 LT with 180,000 miles my check engine light recently came on and I had it scanned .
the only code that comes up is P0496 High Purge Flow. The car runs fine just except when I stop to get gas then the car has trouble starting, it will take 3 or 4 times and then it usually stalls but once it starts up it idles up and down and sounds terrible for about 10 seconds or so then the car runs fine again until I stop to get more gas then same thing happens again.

I have replaced the gas cap , the purge vent valve solenoid(by the gas tank in the canister) , the fuel tank pressure sensor and have also replaced the purge vent valve(on top of the motor) and I also have checked all the wiring and connectors to all the sensors and they all have juice going to them.

and I'm still having the same issues with the car after getting gas and my check engine light is still on with the same code . ( I also cleared the code after replacing all the sensors and the gas cap but the light came back on with the same P0496 code)

its starting to get frustrating that's why I'm here. I'm hoping someone out there might have some more insight from where I can go from here or maybe some steps I can take to test a thing or to?

Thanks again in advance !

Discretesignals
Ultimate Carjunky / Moderator
Discretesignals profile image

Jan 27, 2015, 4:35 PM

Post #2 of 3 (1956 views)

Re: P0496 High purge Flow ....help	Sign In

Disconnect the purge control valve (not the vent valve) electrical connector. Then disconnect the line that goes to the purge control valve from the charcoal canister. Start the engine and feel for vacuum on the end of the purge valve nipple. If you have vacuum, replace the purge control valve.

Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.

(This post was edited by Discretesignals on Jan 27, 2015, 4:37 PM)

LuckyDogLD
New User

Jan 28, 2015, 5:16 AM

Post #3 of 3 (1942 views)

Re: P0496 High purge Flow ....help	Sign In

Thanks a lot for the tip!
I did exactly what you said and there was vacuum. I went back to auto zone and they traded the part in for a new one, I guess it has a lifetime warranty on it. I just put the new valve on about to take it a drive and see what happens.. Damn cheap parts..
Thanks again Discretesignals

Email This Post

Search for (options) Privacy Sitemap