Main IndexAuto Repair Home Search Posts SEARCH
POSTS 		Who's Online WHO'S
ONLINE 		Log in LOG
IN




Automotive Repair
Car Troubleshooting Topics
  Car Troubleshooting
  Engine Troubleshooting
  Engine Fault Codes
  Electrical and Wiring
  Transmission Problems

Car Repair Topics
  Car Making Noises
  Car Stereo Repair
  Heating or AC Issues
  Motorcycles and ATVs
  Tricks of the Trade
  Truck Repair Advice

Site Options:   
  Login
  Sign up here!



Latest Forum Post
with_replies.gif image   Lukewarm Heat............
New antifreeze reverse flush heater core...

with_replies.gif image   multiple warning lights
2013 GMC Terrain 130,000 miles 4 cylinde...

with_replies.gif image   2014 Nissan Sentra Shaking
Car recently started shaking when accele...

no_replies.gif image   Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086
N/A

hot_with_replies.gif image   1989 toyota pickup 3.0 crank no start
I have a 1989 toyota pickup 3.0 crank no...

with_replies.gif image   Strut spring orientation and strut mount tension nut
2017 Nissan rogue awd 2.5 L Put in Monro...

with_replies.gif image   Transmission stuck in part, I have tried everything
So I'm working on my elderly fathers 201...

with_replies.gif image   2017 dodge journey LED headlights on/off randomly
Year of vehicle 2017 Make of vehicle dod...

with_replies.gif image   Kia Soul starter replacement issues!
Okay so my car is a 2010 Kia soul 2.0 en...

hot_with_replies.gif image   Please Help - Knock sound & engine fail
Hi all, Hoping to get some insight and ...




SES light dimms when getting codes!!!

Search for (search options)
 



ohhwell
New User

Feb 23, 2007, 7:23 AM

Post #1 of 3 (2211 views)
SES light dimms when getting codes!!! Sign In
Hi,
I think this would be the best section to post this in. I have a code scanner that blinks the Check Engine light to report codes. When I am getting the codes from my 1988 V1500 Suburban, The code 12 starts to report fine then it start to blink slightly erratic and then dims. AFter the 3rd repitition of the code 12 I can barely make out another code that could be a 24 or 34 but it's hard to tell. If I turn the truck off and try again, it is still too dim or just completely dark from the start. If I let it sit for a bit, It starts out fine again but gets dim the same. When The scanner is not attached, the Check Engine light is bright and fine. Using the same scanner on my 94 Saturn, it works just fine. Does this mean there is something wrnog with the computer in my truck???

Thanks for any help.

-Pat


steve01832
Veteran
steve01832 profile image

Feb 24, 2007, 4:59 AM

Post #2 of 3 (2201 views)
Re: SES light dimms when getting codes!!! Sign In
Not necessarily, compatibility may be an issue or even a weak battery. You don't need a scan tool for this truck to retrieve codes. You can take a paperclip bent into a horseshoe and ground the ALDL connector with the key on engine off. The check engine light will begin to flash out the codes this way.

Steve


DanD
Veteran / Moderator
DanD profile image

Feb 24, 2007, 5:48 AM

Post #3 of 3 (2200 views)
Re: SES light dimms when getting codes!!! Sign In
Steve has the right idea by jumpering the ALDL connector to see if it’s your reader or whether it’s the computer that has lost diagnostic capabilities.
Connect the paper clip or whatever between A&B terminals and then turn the ignition on. The Check engine light should flash 12 telling you that it’s entered diagnostics and then flash trouble codes if any. It should flash each code three times and then start over again with code 12.
If you were to start the truck with the ALDL jumpered the check engine light will or should flash quickly while the system is in open loop and then begin to flash much slower after the O2 has come on line (closed loop).
Light on is a lean indication, O2 voltage above 450mv; light out rich indication O2 voltage below 450mv.
Here a diagram showing the ALDL and the terminal designations.
Dan.




Canadian "EH"









 
 
 






Search for (options) Privacy Sitemap