|
|
|
1996 grand am security light
|
|
|
| |
|
|
drcjl13708
Novice
Apr 25, 2010, 12:39 PM
Post #1 of 9
(2358 views)
|
|
1996 grand am security light
|
Sign In
|
|
I am haveing soooooo much trouble with this security light thing. I was able to clear code and get car started again, but i am over mesing with this. Does anyone know of a way to get rid of this system all together? Car starts then stalls, I found a way to clear codes and get it to run again, but for how long not sure? If I can just shortcut around this security system it seems like it would be so much easier.
(This post was edited by drcjl13708 on Apr 25, 2010, 2:15 PM)
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Apr 25, 2010, 2:12 PM
Post #2 of 9
(2354 views)
|
|
Re: 1996 grand am security light
|
Sign In
|
|
You can't entirely get rid of the system because it is integrated through the operating system although the most common failure is the sensor in the ignition switch and that can be bypasssed although the rest of the system has to be operational.
If you find the black wire and the yellow wire from the passlock sensor in the column you can solder in a 2.2 K ohm resistor and then attempt to start the car.It will stall don't turn the ignition off.Let the ignition on for ten minutes or until the theft light goes out.Turn the key off for ten seconds then attempt to start the car.If it now runs you have been successful.If it doesn't you either made a mistake or there are other problems besides the ignition lock cylinder.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
drcjl13708
Novice
Apr 25, 2010, 2:22 PM
Post #3 of 9
(2350 views)
|
|
Re: 1996 grand am security light
|
Sign In
|
|
WOW that sound like alot of effort. But first you said some times it just the ignition switch? does that mean the key switch in the coloum?
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Apr 25, 2010, 2:44 PM
Post #4 of 9
(2346 views)
|
|
Re: 1996 grand am security light
|
Sign In
|
|
It's the ignition lock cylinder which isn't such a minor thing because it contains the Passlock cylinder. It's not a lot of work to bypass it. It's just a matter of finding 2 wires and splicing a resister between them and then perform the rerlearn. Your alternative is to let the dealer diagnose and repair it for a few hundred dollars.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
drcjl13708
Novice
Apr 25, 2010, 6:04 PM
Post #5 of 9
(2340 views)
|
|
Re: 1996 grand am security light
|
Sign In
|
|
ok heck it's worth a shot. It's goota be beeter then what i have been dealling with. I think I am gonna wait till the week end though. It might take me a little while. But i gonna try to get the resister and soldering iron this week, reckon just a Radio Shack items?
|
|
| |
|
|
drcjl13708
Novice
Apr 26, 2010, 9:50 AM
Post #6 of 9
(2331 views)
|
|
Re: 1996 grand am security light
|
Sign In
|
|
i do have one more question in reguards to that 96 grand am. OMLY when makeing a right turn I hear a rubbing or light grinding noice. Checked all places to see NO signs of tires rubind. Ran car in reverce turning wheel ALL the way in both directions and no noice at all. And noice is not heard when making left turn. If making right turn and accelerate VERY slowly then no noice but drive normaly, and stop then make a right turn then there the noise is again. any ideas?
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Apr 26, 2010, 3:35 PM
Post #7 of 9
(2325 views)
|
|
Re: 1996 grand am security light
|
Sign In
|
|
You need to jack up the front end and check the wheel bearings first. Check the backing plates behind the rotors and see if one is close enough to touch the rotor when the wheel leans a little. If it's too close, just pull it away a little bit.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
dollarpoor59
New User
Jun 5, 2010, 10:50 AM
Post #8 of 9
(2290 views)
|
|
Re: 1996 grand am security light
|
Sign In
|
|
i have same problem 96 grand prix , won"t start new key and chip ,now its but lite still on . so i guess 10 min. ,10 sec. don"t work it"S module ? what you do?
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 5, 2010, 11:37 AM
Post #9 of 9
(2285 views)
|
|
Re: 1996 grand am security light
|
Sign In
|
|
You need to start a fresh question on your own car please. We don't address multiple cars in one question.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
Lukewarm Heat............
Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086
1989 toyota pickup 3.0 crank no start
