|
|
|
2000 ford E250 temp gauge
|
|
|
| |
|
|
jse
Novice
Mar 12, 2014, 9:44 PM
Post #1 of 12
(4498 views)
|
|
2000 ford E250 temp gauge
|
Sign In
|
|
Driving along in my 2000 ford E250 5.4 l v8 when all of a sudden temp gauge pins on hot oil light comes on van loses power, but continues to run. I pull over shut it off restart (sometimes 2-3 times) and all is normal. What could cause this to happen?
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Mar 12, 2014, 10:01 PM
Post #2 of 12
(4488 views)
|
|
Re: 2000 ford E250 temp gauge
|
Sign In
|
|
Temp shows hot and oil warning? Have you even checked levels of coolant and oil yet? Still driving or trying is just going to make this kill itself and it seems to be warning you,
T
|
|
| |
|
|
jse
Novice
Mar 12, 2014, 10:03 PM
Post #3 of 12
(4484 views)
|
|
Re: 2000 ford E250 temp gauge
|
Sign In
|
|
Yes everything is fine.
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Mar 12, 2014, 10:19 PM
Post #4 of 12
(4482 views)
|
|
Re: 2000 ford E250 temp gauge
|
Sign In
|
|
What is "hot oil" light on this meant for? Transmission something?
Need codes read if fluids are really fine. The temp suddenly spiking up and loss of power something is really happening not just an error in the gauge IMO so needs attention right away starting with a code reading - and don't force this to run if not right as it will just make things worse,
T
|
|
| |
|
|
GC
User
Mar 13, 2014, 6:30 AM
Post #5 of 12
(4456 views)
|
|
Re: 2000 ford E250 temp gauge
|
Sign In
|
|
I think there was supposed to be a comma there Tom. (gauge pins on hot, oil light comes on) I think....
____________________________________________________
Willing to help, willing to learn... Rob
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Mar 13, 2014, 6:38 AM
Post #6 of 12
(4451 views)
|
|
Re: 2000 ford E250 temp gauge
|
Sign In
|
|
Probably a faulty CHT sensor.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
|
jse
Novice
Mar 13, 2014, 6:41 AM
Post #7 of 12
(4448 views)
|
|
Re: 2000 ford E250 temp gauge
|
Sign In
|
|
I've had my mechanic take a look at it twice. But every time I get it in there its not doing it anymore. The reader shows that it overheated. He said I might be the temp sensor. But can't be sure unless he can get the reader on when its doing its thing.
(This post was edited by jse on Mar 13, 2014, 6:44 AM)
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Mar 13, 2014, 6:50 AM
Post #8 of 12
(4439 views)
|
|
Re: 2000 ford E250 temp gauge
|
Sign In
|
|
Maybe try this: Put a thermo in floor heater outlet and set heat to warmest. Once warmed up it should stay about the same. If it fluctuated or goes cold at the time gauge says "hot" it really is hot IMO. Boiling means vapor which doesn't transfer heat and messes with sensors.
Just do anything not to overheat or run on low oil pressure whatever this intermittent thing is it's worth paying strict attention to,
T
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Mar 13, 2014, 7:08 AM
Post #9 of 12
(4429 views)
|
|
Re: 2000 ford E250 temp gauge
|
Sign In
|
|
Have your mechanic monitor the CHT temperature sensor on his/her scan tool. See if wiggling the CHT electrical connector/harness or tapping on the sensor with a screw driver gets it to act up. The CHT is located on the left hand cylinder head. You don't have to drain the coolant to change it.
If the sensor shows the head temperature getting above 260F, the PCM will go into overheat protection mode. It will cause the temp gauge to peg, hot lights come on, and fuel injectors to be cut off. If it shows 330F or more, the PCM will disable all the injectors and the engine won't start.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Mar 13, 2014, 7:13 AM)
|
|
| |
|
|
jse
Novice
Mar 13, 2014, 4:51 PM
Post #10 of 12
(4412 views)
|
|
Re: 2000 ford E250 temp gauge
|
Sign In
|
|
It did it again this morning. It turns out that even though the hoses and radiator did not feel hot to the touch the anti freeze level was down by half 2.5 gal . The radiator is new 3 months old and there is no visible signs of a leak anywhere. Also no water on the dipstick. Will have to monitor it and search for some kind of leak.
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Mar 13, 2014, 5:02 PM
Post #11 of 12
(4405 views)
|
|
Re: 2000 ford E250 temp gauge
|
Sign In
|
|
Have the coolant system pressure tested when the engine is cold, you'll find the leak. I'm surprised your mechanic never thought to inspect the coolant level...hmmm
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Mar 13, 2014, 5:33 PM)
|
|
| |
|
|
jse
Novice
Mar 13, 2014, 5:44 PM
Post #12 of 12
(4396 views)
|
|
Re: 2000 ford E250 temp gauge
|
Sign In
|
|
HMMMMMMMMMm is right my thoughts exactly. Thanks for all the help
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
Lukewarm Heat............
Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086
1989 toyota pickup 3.0 crank no start
