2001 Ford Taurus SES engine misfire - Engine Troubleshooting


	Auto Repair Home	SEARCH POSTS	WHO'S ONLINE	LOG IN

Automotive Repair

Car Troubleshooting Topics
  Car Troubleshooting
  Engine Troubleshooting
  Engine Fault Codes
  Electrical and Wiring
  Transmission Problems

Car Repair Topics
  Car Making Noises
  Car Stereo Repair
  Heating or AC Issues
  Motorcycles and ATVs
  Tricks of the Trade
  Truck Repair Advice

Site Options:
  Login
  Sign up here!

Latest Forum Post

Lukewarm Heat............

New antifreeze reverse flush heater core...

multiple warning lights

2013 GMC Terrain 130,000 miles 4 cylinde...

2014 Nissan Sentra Shaking

Car recently started shaking when accele...

Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086

N/A

1989 toyota pickup 3.0 crank no start

I have a 1989 toyota pickup 3.0 crank no...

Strut spring orientation and strut mount tension nut

2017 Nissan rogue awd 2.5 L Put in Monro...

Transmission stuck in part, I have tried everything

So I'm working on my elderly fathers 201...

2017 dodge journey LED headlights on/off randomly

Year of vehicle 2017 Make of vehicle dod...

Kia Soul starter replacement issues!

Okay so my car is a 2010 Kia soul 2.0 en...

Please Help - Knock sound & engine fail

Hi all, Hoping to get some insight and ...

2001 Ford Taurus SES engine misfire

Sign up here!

Search for (search options)

Auto Repair Home>> Automotive Repair>> Engine Troubleshooting

mboyce
New User

Aug 21, 2011, 2:02 PM

Post #1 of 3 (6059 views)

2001 Ford Taurus SES engine misfire	Sign In

Hello all, I have a 2001 Ford Taurus SES with the 3.0 OHV engine. Recently the car started running rough and I discovered using an inductive timing light that the #2 and #6 cylinders weren't firing. I went for the easy stuff first by replacing the plugs and plug wires with no change. I then replaced the coil pack figuring that I had a bad coil. Still no change so I then replaced the crank position sensor which was a long shot; but still no change. I have DTC's listed below. Any ideas?

P0353
P0442
P0401
P1401
P0171
P0174
P0306

Discretesignals
Ultimate Carjunky / Moderator
Discretesignals profile image

Aug 21, 2011, 4:09 PM

Post #2 of 3 (6036 views)

Re: 2001 Ford Taurus SES engine misfire	Sign In

The one code that I would be concerned about since you don't appear to have spark on 2 and 6 would be the P0352 code. That means the PCM (powertrain control module) didn't receive an IDM (ignition diagnostic monitor) pulse signal from the ignition control module which is integrated into the PCM. 2 and 6 are companion cylinders. That means they share the same coil.

The IDM pulse is generated from the kickback voltage that occurs when a primary coil's voltage collapses in one of the three primary windings. The IDM pulse is a way for the PCM to verify that a coil has fired once commanded.

Inspect the wiring harness and connectors from the coil pack to the PCM. You may need to check those circuits for the 2&6 coil for continuity and no shorts to ground or power.

At the coil pack the yellow with white striped wire is the 2&6 primary coil ground wire that runs from the coil pack to the PCM. It's a straight shot, no inline connectors between the coil connector and PCM connector. At the PCM the white/yellow wire goes to pin 78 at the PCM connector. If continuity is good and there are no shorts to ground or power, more than likely the PCM is the culprit. There could be a bad coil driver or coil driver circuit in the PCM causing the problem. To verify you would have to connect a 12 V LED test lamp or watch voltage at the PCM connector with a DSO to see if the PCM is triggering the circuit.

Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.

(This post was edited by Discretesignals on Aug 21, 2011, 4:18 PM)

mboyce
New User

Aug 21, 2011, 4:28 PM

Post #3 of 3 (6030 views)

Re: 2001 Ford Taurus SES engine misfire	Sign In

Thank you! This info is very helpful.

Search for (options) Privacy Sitemap