|
|
|
98 Ford Ranger Cyclinder Misfire
|
|
|
| |
|
|
jpope85
New User
Sep 3, 2012, 2:05 PM
Post #1 of 7
(3661 views)
|
|
98 Ford Ranger Cyclinder Misfire
|
Sign In
|
|
98 Ford Ranger // 3.0 Liter // Manual Trans // 80k
Got in my ranger the other day and noticed lack of engine power, as well
as rough idle. Check engine light came on. Autozone diagnosed from
the computer as cyclinder 3 misfire. I replaced all the spark plugs,
cylinder 3's plug was pretty nasty looking, all others were fine. This
didn't fix it. Next I replaced the ignition wire from the coil pack to
the plug and that fixed it, for a few hours, then back to square one.
Should I just keep moving up and replace the coil pack at this point?
Thanks.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Sep 3, 2012, 3:13 PM
Post #2 of 7
(3618 views)
|
|
Re: 98 Ford Ranger Cyclinder Misfire
|
Sign In
|
|
Yep, the coil is too weak. The new wire had lower resistance so it got by with less for a short period. Check the compression on that cylinder to be sure also.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
jpope85
New User
Sep 6, 2012, 5:22 AM
Post #4 of 7
(3563 views)
|
|
Re: 98 Ford Ranger Cyclinder Misfire
|
Sign In
|
|
Changing the coil pack did the trick. I went ahead and finished replacing out all the ignition wires and cleaned off plug3 again. Thanks for the help!
By plug3 looking nasty, just real brown and gunked up looking, I figure because the cylinder wasn't firing.
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Sep 6, 2012, 6:44 AM
Post #5 of 7
(3559 views)
|
|
Re: 98 Ford Ranger Cyclinder Misfire
|
Sign In
|
|
Change out at least THAT plug if not all for exact replacement plugs. If somehow that plug was a cause not the total failure I wouldn't risk it - get it replaced,
T
|
|
| |
|
|
jpope85
New User
Sep 6, 2012, 6:48 AM
Post #6 of 7
(3553 views)
|
|
Re: 98 Ford Ranger Cyclinder Misfire
|
Sign In
|
|
First thing I did was replaced all the plugs, I think I wasn't clear on that, when I said I cleaned it off, that was the new plug after I thought it was fixed. Replacing the Coil Pack was the real issue. Thanks. Its running better than ever now.
(This post was edited by jpope85 on Sep 6, 2012, 6:50 AM)
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Sep 6, 2012, 7:08 AM
Post #7 of 7
(3550 views)
|
|
Re: 98 Ford Ranger Cyclinder Misfire
|
Sign In
|
|
I hear you. You needed to clean that plug and even if new it would worry me. Probably if anything would have less resistance to spark or ground out now but if somehow that stresses the coil I'd want it out. Just me,
T
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
1989 toyota pickup 3.0 crank no start
Please Help - Knock sound & engine fail
