|
|
ZuuL
User
Jun 21, 2010, 1:59 AM
Post #1 of 10
(2221 views)
|
|
98 Plymouth Breeze
|
Sign In
|
|
The thing won't start right now it just makes noise ,like a buzz and click ,it won't turn over at all.
Although it won't turn over right now my fresh charged battery turned it over the first time but not fast enough to start it ,i just sits now.
If it's the battery how long and what setting do i charge it at , i have a 2/10/50 schumacher battery charger. Can i use the 50 amp with the battery to start my car?
Could it be the starter?
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Jun 21, 2010, 6:15 AM
Post #2 of 10
(2215 views)
|
|
Re: 98 Plymouth Breeze
|
Sign In
|
|
That's typical of bad battery cable connections or cables. Both ends - not just at the battery. Charge at 2 amp overnite is my choice but takes a long time. Duh, 10 is faster and good too. I'd reserve using 50 amp for when you are short of time but that still isn't wildly excessive. Batteries like and get a better charge when slower as IMO much less damaging,
T
|
|
| |
|
|
nickwarner
Veteran
/ Moderator
Jun 21, 2010, 12:30 PM
Post #3 of 10
(2206 views)
|
|
Re: 98 Plymouth Breeze
|
Sign In
|
|
One question here? Do you know the battery is freshly charged because you charged it up and had it tested or because it sat on a charger for a while. If the battery is no good, no amount of charging will remedy the problem.
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Jun 21, 2010, 1:29 PM
Post #4 of 10
(2202 views)
|
|
Re: 98 Plymouth Breeze
|
Sign In
|
|
Good catch Nick. That's why you make the big bucks!
T
|
|
| |
|
|
ZuuL
User
Jun 22, 2010, 3:33 AM
Post #5 of 10
(2191 views)
|
|
Re: 98 Plymouth Breeze
|
Sign In
|
|
The thing is i have a good multi meter but i just haven't learned how to use it.
So to check the battery power i set it to DC and that gives me voltage but do i need to check the amperage to?
Can i check with the multi meter if the battery is damaged inside to the point it will only charge so so?
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Jun 22, 2010, 5:00 AM
Post #6 of 10
(2187 views)
|
|
Re: 98 Plymouth Breeze
|
Sign In
|
|
Set you meter to DC voltage. A normal 12v battery just sitting there should read real close to 12.6 volts. Since there's no quick way to load test it use the car. Watching voltage request starter and see what happens. Check at both battery itself and at the cables. Then again at opposite ends of cables can show voltage drops when a load from the car is put on battery.
Since it wont start try using headlights and blower motor both at once and see how long it can hold a decent voltage. If not long the battery is in question,
T
|
|
| |
|
|
ZuuL
User
Jun 22, 2010, 8:42 PM
Post #7 of 10
(2174 views)
|
|
Re: 98 Plymouth Breeze
|
Sign In
|
|
OK ,i finally got her charged ,12 hours or so on 2amp overnight but no cigar. Also checked it with the multi meter and got about 11.50v at 4.5 amps
I put it in nice and tight got a little noise/click dash was on/wipers but nothing was moving. Second time i tried to locate the started to tap it a little but i'm not sure if that was it.
After the first time that was it ,wouldn't even turn on the lights so i'm gonna get a new battery unless you have any other suggestions.
It's on warranty i just got to find the papers.
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Jun 22, 2010, 9:49 PM
Post #9 of 10
(2166 views)
|
|
Re: 98 Plymouth Breeze
|
Sign In
|
|
I'm not totally sure what you meant by 11.5 volts after a charge? If so the battery is junk,
T
|
|
| |
|
|
ZuuL
User
Jun 23, 2010, 3:50 AM
Post #10 of 10
(2158 views)
|
|
Re: 98 Plymouth Breeze
|
Sign In
|
|
Yep it's junk because i overnight charged it again and tried today ,same 11.50
New battery time
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
1989 toyota pickup 3.0 crank no start
Please Help - Knock sound & engine fail
