|
|
did my truck jump time????
|
|
|
| |
|
richardlice
User
Jun 1, 2011, 5:39 PM
Post #1 of 48
(15703 views)
|
did my truck jump time????
|
Sign In
|
|
my truck is a 1996 chevy 3500 5.7 ltr. i was driving and it started to miss really bad then it died, all of the power cut off to everything, tried to start again it cranked and ran really bad and died again now i cant get it to crank anymore. i have 11.8 v to the coil is this enough? all my wires seem to be connected well. i called around to try and find a set of Noid lights and cant get any at my local auto parts store, is there another test to see if the injection system works fine. i have about 35 psi in fuel just changed the fuel filter. the fuel pump kicks on when i cycle the key on. i took the distributor off and had my brother crank it the rotor turns only when i help it a little, then it stops, i also looked inside the valve cover and the lifters seem to work when cranking, please help
|
|
| |
|
Mr.scotty
Enthusiast
Jun 1, 2011, 5:44 PM
Post #2 of 48
(15701 views)
|
Re: did my truck jump time????
|
Sign In
|
|
Sounds like you found your problem. The rotor should always turn by it's self. Maybe the rotor it's self is broke if not then the distributor gear is probably stripped. -------------------------------------------------------- Your only as good as your tools!
|
|
| |
|
richardlice
User
Jun 1, 2011, 5:48 PM
Post #3 of 48
(15698 views)
|
Re: did my truck jump time????
|
Sign In
|
|
do you have or know where to get a diagram on how to change the distributor
|
|
| |
|
Mr.scotty
Enthusiast
Jun 1, 2011, 5:52 PM
Post #4 of 48
(15693 views)
|
Re: did my truck jump time????
|
Sign In
|
|
I do not. But you can just do a google search or if one of the other users on here (hammer time) chimes in he might have one for you. A repair manual would be a good idea to have you know, There about $20-25 bucks at autoparts stores. -------------------------------------------------------- Your only as good as your tools!
|
|
| |
|
Mr.scotty
Enthusiast
Jun 1, 2011, 6:01 PM
Post #5 of 48
(15687 views)
|
Re: did my truck jump time????
|
Sign In
|
|
-------------------------------------------------------- Your only as good as your tools!
(This post was edited by Mr.scotty on Jun 2, 2011, 7:42 AM)
|
|
| |
|
richardlice
User
Jun 1, 2011, 6:20 PM
Post #6 of 48
(15681 views)
|
Re: did my truck jump time????
|
Sign In
|
|
thanks im starting the teardown first thing in the morning. ill let ya know how it turned out
|
|
| |
|
Mr.scotty
Enthusiast
Jun 1, 2011, 6:50 PM
Post #7 of 48
(15672 views)
|
Re: did my truck jump time????
|
Sign In
|
|
Great let me know. -------------------------------------------------------- Your only as good as your tools!
|
|
| |
|
richardlice
User
Jun 1, 2011, 8:55 PM
Post #8 of 48
(15666 views)
|
Re: did my truck jump time????
|
Sign In
|
|
one more question all of this says you only have to get close that you can time it after, my truck has a warning that states that the timing is set automatically not to try and adjust the timing is this going to affect the way i need to install?
|
|
| |
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 2, 2011, 5:04 AM
Post #9 of 48
(15655 views)
|
Re: did my truck jump time????
|
Sign In
|
|
That's correct. You cannot change timing. Turning the distributor changes the synch between the cam sensor and the Cranks sensor and any more than 4 degrees off and it will run bad and put the check engine light on. It requires a professional scan tool to set it correctly. There is a PID in there called Cam Offset and it has to be adjusted to zero. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
Mr.scotty
Enthusiast
Jun 2, 2011, 7:41 AM
Post #10 of 48
(15648 views)
|
Re: did my truck jump time????
|
Sign In
|
|
Heres the same thing i posted but with some pics. Hope this helps you out more then the last one. A. Here is the procedure. IMPORTANT: Rotate the number 1 cylinder to Top Dead Center (TDC) of the compression stroke. The engine front cover has 2 alignment tabs and the crankshaft balancer has 2 alignment marks (spaced 90° apart) which are used for positioning number 1 piston at Top Dead Center (TDC) . With the piston on the compression stroke and at top dead center, the crankshaft balancer alignment mark (1) must align with the engine front cover tab (2) and the crankshaft balancer alignment mark (4) must align with the engine front cover tab (3). - Rotate the crankshaft balancer clockwise until the alignment marks on the crankshaft balancer are aligned with the tabs on the engine front cover and the number 1 piston is at top dead center of the compression stroke.
- Align white paint mark on the bottom stem of the distributor, and the pre-drilled indent hole in the bottom of the gear (3).
NOTE: The OBD II ignition system distributor driven gear and rotor may be installed in multiple positions. In order to avoid mistakes, mark the distributor on the following components in order to ensure the same mounting position upon reassembly: - The distributor driven gear
- The distributor shaft
- The rotor holes
Installing the driven gear 180 degrees out of alignment, or locating the rotor in the wrong holes, will cause a no-start condition. Premature engine wear or damage may result. - With the gear in this position, the rotor segment should be positioned as shown for a V6 engine (1) or V8 engine (2).
- The alignment will not be exact.
- If the driven gear is installed incorrectly, the dimple will be approximately 180 degrees opposite of the rotor segment when the gear is installed in the distributor.
- Using a long screw driver, align the oil pump drive shaft to the drive tab of the distributor.
- Guide the distributor into the engine. Ensure that the spark plug towers are perpendicular to the centerline of the engine.
- Once the distributor is fully seated, the rotor segment should be aligned with the pointer cast into the distributor base.
- This pointer may have a 6 cast into it, indicating that the distributor is to be used on a 6 cylinder engine or a 8 cast into it, indicating that the distributor is to be used on a 8 cylinder engine.
- If the rotor segment does not come within a few degrees of the pointer, the gear mesh between the distributor and the camshaft may be off a tooth or more.
- If this is the case, repeat the procedure again in order to achieve proper alignment.
- Install the distributor mounting clamp bolt. Tighten the distributor clamp bolt to 25 N.m (18 lb ft).
- Install the distributor cap.
- Install two NEW distributor cap screws. Tighten the screws to 2.4 N.m (21 lb in) .
- Install the electrical connector to the distributor.
- Install the spark plug wires to the distributor cap.
- Install the ignition coil wire. The wire must not touch anything like the dip stick. Rubbing will make a ground/short after time of use.
- For V-8 engines, connect a scan tool.
- Monitor the Camshaft Retard Offset value. Refer to Computers and Control Systems Camshaft Retard Offset Adjustment. IMPORTANT: If the Malfunction Indicator lamp is turned on after installing the distributor, and a DTC P1345 is found, the distributor has been installed incorrectly.
- Refer to Installation Procedure 2 for proper distributor installation.
-------------------------------------------------------- Your only as good as your tools!
|
|
| |
|
richardlice
User
Jun 2, 2011, 10:22 AM
Post #11 of 48
(15638 views)
|
Re: did my truck jump time????
|
Sign In
|
|
yep definately the distributor, half the splines are gone on the gear. should i worry about metal shavings?
|
|
| |
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 2, 2011, 11:29 AM
Post #12 of 48
(15630 views)
|
Re: did my truck jump time????
|
Sign In
|
|
Be a good idea to change the oil when you're done. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
richardlice
User
Jun 2, 2011, 4:56 PM
Post #13 of 48
(15620 views)
|
Re: did my truck jump time????
|
Sign In
|
|
finished everything still all crank no start it seems like its off time . what do i do next?
|
|
| |
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 2, 2011, 4:59 PM
Post #14 of 48
(15613 views)
|
Re: did my truck jump time????
|
Sign In
|
|
Why, is it backfiring or anything? It probably is out of time. Make sure you have it up on TDC on the compression stroke. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
richardlice
User
Jun 2, 2011, 5:03 PM
Post #15 of 48
(15609 views)
|
Re: did my truck jump time????
|
Sign In
|
|
no back fire, i have spark and fuel, i put my finger on the #1 and when it blew off i stopped and then lind up the mark on the balancer. then i put the dist. in facing the #1 node in the cap just like the instructions.
|
|
| |
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 2, 2011, 5:08 PM
Post #16 of 48
(15594 views)
|
Re: did my truck jump time????
|
Sign In
|
|
That's not what the instructions say to do. If you look inside that cap, the outside wire position doesn't align with the inside contact. You have to align it with the #1 in the diagram, not the number one wire. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
richardlice
User
Jun 2, 2011, 6:28 PM
Post #17 of 48
(15588 views)
|
Re: did my truck jump time????
|
Sign In
|
|
thats what i said in the cap
|
|
| |
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 2, 2011, 6:31 PM
Post #18 of 48
(15581 views)
|
Re: did my truck jump time????
|
Sign In
|
|
And that's what I said that you weren't supposed to do. The alignment doesn't match. Use the diagram. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
richardlice
User
Jun 2, 2011, 6:56 PM
Post #19 of 48
(15579 views)
|
Re: did my truck jump time????
|
Sign In
|
|
how much voltage does the coil need
|
|
| |
|
richardlice
User
Jun 2, 2011, 7:13 PM
Post #20 of 48
(15576 views)
|
Re: did my truck jump time????
|
Sign In
|
|
ohhhhh duh im one tooth off then sorry hammer
|
|
| |
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 2, 2011, 7:16 PM
Post #21 of 48
(15572 views)
|
Re: did my truck jump time????
|
Sign In
|
|
What a surprise ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
richardlice
User
Jun 2, 2011, 7:22 PM
Post #22 of 48
(15567 views)
|
Re: did my truck jump time????
|
Sign In
|
|
im going to start over in the morning, also what kind of voltage should be getting to the coil to work properly i have a feeling its a combination of stuff, besides me being dumb
|
|
| |
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 2, 2011, 7:24 PM
Post #23 of 48
(15555 views)
|
Re: did my truck jump time????
|
Sign In
|
|
The coil uses battery voltage. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
richardlice
User
Jun 2, 2011, 7:25 PM
Post #24 of 48
(15550 views)
|
Re: did my truck jump time????
|
Sign In
|
|
so if the battery is low on charge then the coil wont fire or will it
|
|
| |
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 2, 2011, 7:27 PM
Post #25 of 48
(15534 views)
|
Re: did my truck jump time????
|
Sign In
|
|
If there's enough voltage to crank the engine over, there will be enough for the coil. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|