|
|
|
engine running rugh (shaking) bad
|
|
|
| |
|
|
meloyebo
New User
Apr 27, 2012, 8:54 AM
Post #1 of 7
(2406 views)
|
engine running rugh (shaking) bad
|
|
|
Hi, 03 Ford ranger PU 3.0 6 cil ac 86K
was tune up 8 month ago, starting missing going up hills, so i replaced the plugs, bad advice from a friend.
now its running to a point that feels that will cut off any time.
any ideas?
|
|
| |
|
|
nickwarner
Veteran
/ Moderator
Apr 27, 2012, 2:49 PM
Post #2 of 7
(2373 views)
|
|
Re: engine running rugh (shaking) bad
|
|
|
Your friend may have saved you future issues, just didn't fix this one. At that mileage you were due for plugs. Get the codes pulled and post the code numbers here. We need the exact numbers, for example P0300 random cyl misfire. Generic descriptions don't help. With the numbers we can narrow it down. Some parts stores offer this service for free.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Apr 27, 2012, 3:38 PM
Post #3 of 7
(2368 views)
|
|
Re: engine running rugh (shaking) bad
|
|
|
It's never a bad idea to replace spark plugs. The problem comes when it isn't done right or needs a lot more than the plugs.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
meloyebo
New User
May 2, 2012, 3:06 PM
Post #4 of 7
(2305 views)
|
|
Re: engine running rugh (shaking) bad
|
|
|
Thank you guys for helping. plug the hand held annalizer and no codes show
back to square one. am suspecting on : new set of plug wires, engine temp sensor, oxigen sensor.
am using 93 octane fuel and runs a little better. but still shakes and engine light flashes.
your advise is?
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
May 2, 2012, 3:37 PM
Post #5 of 7
(2301 views)
|
|
Re: engine running rugh (shaking) bad
|
|
|
You really shouldn't drive it any more until you figure out why it is missing. If the light is flashing and you have either a mechanical problem with the engine or an ignition problem, you'll end up cooking the catalytic converter.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
|
meloyebo
New User
May 5, 2012, 12:25 AM
Post #6 of 7
(2274 views)
|
|
Re: engine running rugh (shaking) bad
|
|
|
thank you! you were close, it was ignition problem.
the coil was bad and I replace the wire cables too. truck its running very smooth. total cost $ 130.00 plus my labor :)
thank you again.
meloyebo
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
May 5, 2012, 7:09 AM
Post #7 of 7
(2262 views)
|
|
Re: engine running rugh (shaking) bad
|
|
|
Good to see that you got it straightened out.  Thanks for the follow up. Locking to prevent spam and hijacking. Can be reopened upon request from OP.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
1989 toyota pickup 3.0 crank no start
Please Help - Knock sound & engine fail
