Main IndexAuto Repair Home Search Posts SEARCH
POSTS
Who's Online WHO'S
ONLINE
Log in LOG
IN









jJeep Wrangler low oil pressure


Search for (search options)
 



coolcat2020
New User

Jul 24, 2011, 5:16 PM

Post #1 of 8 (2779 views)
jJeep Wrangler low oil pressure Sign In

I have a 2000 Jeep Wrangler with a 2.5 4cylinder motor with 135,000 miles. The compression on all cylinders was aroun 90-100 so I had the head rebuilt and the head surfaced. While doing this found the rings were also bad. I then put a new crank kit new pistons and rings, new oil pump, checked cam for size and it was ok, new cam bearings were installed by a reputable machine shop, the manifold was cracked so I replaced that with a new one.When the Jeep gets warm the oil pressure dropped to zero at idle, runs 40-50 psi when at travelling speed, I replaced the oil pump again, that didn't help.


zmame
Veteran / Moderator
zmame profile image

Jul 24, 2011, 9:21 PM

Post #2 of 8 (2771 views)
Re: jJeep Wrangler low oil pressure Sign In

Did you or the machine shop put the crank in.. When you installed the crank did you use plastgauge to make sure the clearances where in spec.. You have to be loosing oil pressure somewhere.
Also is the pressure higher cold then hot?.
Is this on dummy gauge or actual mechancal gauge?


(This post was edited by zmame on Jul 27, 2011, 4:37 AM)


coolcat2020
New User

Jul 26, 2011, 6:39 PM

Post #3 of 8 (2747 views)
Re: jJeep Wrangler low oil pressure Sign In

the macjhine shop replaced the cam, I am sure they used plastigauge, it only looses pressure when the engine warms up and is at an idle


Hammer Time
Ultimate Carjunky / Moderator
Hammer Time profile image

Jul 26, 2011, 6:48 PM

Post #4 of 8 (2744 views)
Re: jJeep Wrangler low oil pressure Sign In

He asks about a crank and you respond about a cam...................



~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.



coolcat2020
New User

Jul 27, 2011, 6:41 AM

Post #5 of 8 (2727 views)
Re: jJeep Wrangler low oil pressure Sign In

Forgive me, I meant crank


zmame
Veteran / Moderator
zmame profile image

Jul 28, 2011, 2:51 PM

Post #6 of 8 (2715 views)
Re: jJeep Wrangler low oil pressure Sign In

So did you install the cam or the crank?


coolcat2020
New User

Jul 28, 2011, 6:04 PM

Post #7 of 8 (2709 views)
Re: jJeep Wrangler low oil pressure Sign In

I installed the cam, but the shop installed the cam bearings and miced the cam for me


zmame
Veteran / Moderator
zmame profile image

Jul 29, 2011, 4:36 AM

Post #8 of 8 (2697 views)
Re: jJeep Wrangler low oil pressure Sign In

Lack of lubrication is one of the most common causes of camshaft failure during the initial start-up. If the camshaft and other valve train components are not properly pre-lubricated, they can be damaged within the first few camshaft revolutions. Very clean when building always keep your work area clean and all your components must be cleaned %100. DO NOT let it idle. It is essential to run the engine at 1500-2000 RPM for at least 20 minutes.

You will have to disassemble and see what has failed.






 
 
 






Search for (options) Privacy Sitemap