|
|
strikeeeer
User
Jul 13, 2011, 8:38 AM
Post #1 of 9
(1402 views)
|
|
loose spark 10 seconds
|
Sign In
|
|
1998 gmc serria 1500 5.7 It starts when cold but runs 10-15 seconds and looses spark.I replaced coil,ing. mod. ,camshaft sen. ,6 months ago crankshaft sen.grounds to firewalland engine to frame.When spark gone have 10.9 volts to coil.Thanks for and help.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jul 13, 2011, 11:02 AM
Post #2 of 9
(1392 views)
|
|
Re: loose spark 10 seconds
|
Sign In
|
|
Try unplugging the oil pressure sender
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
strikeeeer
User
Jul 14, 2011, 6:48 AM
Post #3 of 9
(1379 views)
|
|
Re: loose spark 10 seconds
|
Sign In
|
|
I unplugged it it stsrts but will not stay running ,it also after starting a couple times starts like my timing is off.But it starts each time I try.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jul 14, 2011, 7:00 AM
Post #4 of 9
(1377 views)
|
|
Re: loose spark 10 seconds
|
Sign In
|
|
Have you tested the charging system voltage?
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
strikeeeer
User
Jul 14, 2011, 11:29 AM
Post #5 of 9
(1363 views)
|
|
Re: loose spark 10 seconds
|
Sign In
|
|
Took alt. in check fine.Going to take new ing.mod in and have checked.Starts each time but runs 10 15 seconds and quits.Have 62lbs at rail.Battery only at 60% charge.
They could not check, they tried but new and old failed .Thanks for your input Hammertime
(This post was edited by strikeeeer on Jul 14, 2011, 10:17 PM)
|
|
| |
|
|
strikeeeer
User
Jul 15, 2011, 9:57 PM
Post #6 of 9
(1341 views)
|
|
Re: loose spark 10 seconds
|
Sign In
|
|
Dont know what I did but took ing.mod ,camshaft sen. to have check they could not check .Put everything back together,oil sen. back on and it started right up and seems to be running fine.Again Thanks Hammertime.Sorry for response.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jul 16, 2011, 3:23 AM
Post #7 of 9
(1336 views)
|
|
Re: loose spark 10 seconds
|
Sign In
|
|
Must have been something you handled. Let's see what happens now.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
strikeeeer
User
Jul 17, 2011, 8:20 PM
Post #8 of 9
(1318 views)
|
|
Re: loose spark 10 seconds
|
Sign In
|
|
Well it did not work.Now it runs about 5-6 miles then it starts to run with a feeling like it is pulsating then just stops.Cools down starts back up.Once it stops does not start till it cools down.Help!!!!!!!!!!!!!!
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jul 18, 2011, 2:54 AM
Post #9 of 9
(1310 views)
|
|
Re: loose spark 10 seconds
|
Sign In
|
|
All "crank, no start" conditions are approached in the same way. Every engine requires certain functions to be able to run. Some of these functions rely on specific components to work and some components are part of more than one function so it is important to see the whole picture to be able to conclude anything about what may have failed. Also, these functions can ONLY be tested during the failure. Any other time and they will simply test good because the problem isn't present at the moment.
If you approach this in any other way, you are merely guessing and that only serves to replace unnecessary parts and wastes money.
Every engine requires spark, fuel and compression to run. That's what we have to look for.
These are the basics that need to be tested and will give us the info required to isolate a cause.
1) Test for spark at the plug end of the wire using a spark tester. If none found, check for power supply on the + terminal of the coil with the key on.
2) Test for injector pulse using a small bulb called a noid light. If none found, check for power supply at one side of the injector with the key on.
3) Use a fuel pressure gauge to test for correct fuel pressure, also noticing if the pressure holds when key is shut off.
4) If all of these things check good, then you would need to do a complete compression test.
Once you have determined which of these functions has dropped out,
you will know which system is having the problem.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
| | |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
Lukewarm Heat............
Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086
1989 toyota pickup 3.0 crank no start
