|
|
|
1996 Grand Am Died - no spark
|
|
|
| |
|
|
Guest
Anonymous Poster
Aug 18, 2006, 4:01 AM
Post #1 of 5
(4311 views)
|
|
1996 Grand Am Died - no spark
|
Sign In
|
|
Hi,
I have a 1996 Pontiac Grand Am with a 3.1L and 208,000 mi. It just stopped running on the highway at normal highway speed. I noticed as I as drifting over to the shoulder the tachometer was erratic moving back and forth from low to high. It would not start so I had it towed. I didn't have any OBD II codes, no blown fuses and has no spark. Any idea what this problem is? Crank position sensor, ing. module, or coil?
Any way to test these componenets?
I also did a compression test to verify that the timing chain didn't break and the compression is good.
Thanks for your help!
|
|
| |
|
|
tiffngary569
New User
Sep 11, 2006, 9:38 PM
Post #2 of 5
(4291 views)
|
|
Re: 1996 Grand Am Died - no spark
|
Sign In
|
|
you could try the ign. module or maybe even the rotor button which is inside the distributor. i had a similar problem on a camaro. we replaced the ign module, rotor button, dist cap, we replaced all kinds of stuff and still didnt get anywhere. we later sold the car for $350 and found out from the new owner that it was the timing chain.
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Sep 12, 2006, 2:15 AM
Post #3 of 5
(4289 views)
|
|
Re: 1996 Grand Am Died - no spark
|
Sign In
|
|
I believe that the 3.1 is an interferance engine and will self destruct if a timing chain breakes but probably would survive jumping a tooth or two. Never heard of one breaking as so many cars here rust out before they wear out, T
|
|
| |
|
|
tiffngary569
New User
Sep 12, 2006, 11:59 AM
Post #4 of 5
(4284 views)
|
|
Re: 1996 Grand Am Died - no spark
|
Sign In
|
|
also if the timing chain has got some teeth missing it could just be off time.
|
|
| |
|
|
AutoTech1971
Novice
Sep 12, 2006, 6:48 PM
Post #5 of 5
(4280 views)
|
|
Re: 1996 Grand Am Died - no spark
|
Sign In
|
|
Usually a crankshaft sensor will set a code. I usually use a scan tool and oscilloscope to test but you might not have any of those tools. You could try testing the crank sensor with a digital multimeter. If the sensor is hard to get to you could try testing it at the ignition control module. If I'm not mistaken a purple or yellow wire, look for wire colors at crank sensor and follow to control module....Hope this helps....Mike
-
Turn the ignition key OFF. -
Unplug the sensor electrical harness and check the terminals for corrosion and damage. -
Check the sensor wiring harness wires for continuity and repair as necessary. -
Attach the sensor harness making sure it is firmly engaged. -
Using a Digital Volt Ohm Meter (DVOM) set on the DC scale, backprobe the sensor signal terminal (terminal A) with the positive lead of the meter and backprobe the sensor ground terminal (terminal B) with the negative lead of the meter. -
Have an assistant crank the engine and observe the meter. -
You should have approximately a 5 volt reference signal pulse. If not the sensor may be defective.
|
|
| |
|
| | |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
Lukewarm Heat............
Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086
1989 toyota pickup 3.0 crank no start
