|
|
|
2005 Grand Am Key has no effect
|
|
|
| |
|
|
pdouc
New User
Aug 10, 2013, 8:40 PM
Post #1 of 3
(1428 views)
|
|
2005 Grand Am Key has no effect
|
Sign In
|
|
My Grand Am with 141,000 miles decided not to start when we returned from a 6 day vacation in another vehicle. The key turns, the symbols all light up and eventually go away except the word "security" wich keeps blinking as long as the key is in the on position. The fuel pump is heard--other than that, no effect is realized by the turning of the key. I've found that the battery is good, I've replaced fuse # 1 (Ignition Switch), and relay # 11 (starter) in the fuse box under the hood. I am suspecting that there is an issue with the security system. What do you think?
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Aug 11, 2013, 4:42 AM
Post #2 of 3
(1418 views)
|
|
Re: 2005 Grand Am Key has no effect
|
Sign In
|
|
You are being locked out by the security system.
Depending why this happened in the first place you may be able to relearn the system. The Passlock sensor in the ignition switch is a common failure.
You can also bypass that sensor if you choose to do so.
PASSLOCK SENSOR BYPASS
If you find the black wire and the yellow wire from the passlock sensor in the column you can solder in a 2.2 K ohm resistor between them and then follow the relearn procedure below. If it now runs you have been successful.If it doesn't you either made a mistake or there are other problems besides the ignition lock cylinder.
You can also just try to do the relearn to get it started temporarily but it may happen again is the sensor is bad
10 Minute Learn Procedure
- Turn ON the ignition, with the engine OFF.
- Attempt to start the engine, then release the key to ON (vehicle will not start).
- Observe the SECURITY telltale, after approximately 10 minutes the telltale will turn OFF.
- Turn OFF the ignition, and wait 5 seconds .
- The vehicle is now ready to relearn the Passlock(TM) Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK.
- Start the engine. The vehicle has now learned the Passlock(TM) Sensor Data Code and/or password.
IMPORTANT: The vehicle learns the Passlock(TM) Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
(This post was edited by Hammer Time on Aug 11, 2013, 4:44 AM)
|
|
| |
|
|
pdouc
New User
Aug 11, 2013, 5:37 AM
Post #3 of 3
(1413 views)
|
|
Re: 2005 Grand Am Key has no effect
|
Sign In
|
|
Thanks for your reply and advice-- I will let you know how things work out!
Well-- I followed the steps for the system re-learn and it worked like a charm! You really know your stuff. I started it a few times without fail. Do you think I could replace the sensor--can it be replaced without a lot of trouble?
Thanks again.
(This post was edited by pdouc on Aug 11, 2013, 6:42 AM)
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
Lukewarm Heat............
Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086
1989 toyota pickup 3.0 crank no start
