Connect

Car Pictures

Shopping

Classifieds

News & Articles

Car Forums

Automotive Links

(Bookmark CarJunky)

	Auto Repair Home	SEARCH POSTS	WHO'S ONLINE	LOG IN

Automotive Repair Car Troubleshooting Topics   Car Troubleshooting   Engine Troubleshooting   Engine Fault Codes   Electrical and Wiring   Transmission Problems Car Repair Topics   Car Making Noises   Car Stereo Repair   Heating or AC Issues   Motorcycles and ATVs   Tricks of the Trade   Truck Repair Advice Site Options:      Login   Sign up here! Latest Forum Post   Lukewarm Heat............ New antifreeze reverse flush heater core...   multiple warning lights 2013 GMC Terrain 130,000 miles 4 cylinde...   2014 Nissan Sentra Shaking Car recently started shaking when accele...   Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086 N/A   1989 toyota pickup 3.0 crank no start I have a 1989 toyota pickup 3.0 crank no...   Strut spring orientation and strut mount tension nut 2017 Nissan rogue awd 2.5 L Put in Monro...   Transmission stuck in part, I have tried everything So I'm working on my elderly fathers 201...   2017 dodge journey LED headlights on/off randomly Year of vehicle 2017 Make of vehicle dod...   Kia Soul starter replacement issues! Okay so my car is a 2010 Kia soul 2.0 en...   Please Help - Knock sound & engine fail Hi all, Hoping to get some insight and ...

Brake Pedal 2 The Floor Sign up here! Search this forum this category all forums for All words Any words Whole Phrase (search options) Auto Repair Home>> Automotive Repair>> Car Troubleshooting Guest Anonymous Poster dtdavis55@sbcglobal.net Aug 27, 2007, 3:38 PM Post #1 of 3 (1183 views) Brake Pedal 2 The Floor Sign In Replaced Pads and shoes on my 92 taraus and the bake pedal goes to the floor. Can pump and get a little bit of brake. Does the master cylinder need replaced? Tom Greenleaf Ultimate Carjunky / Moderator Aug 27, 2007, 6:10 PM Post #2 of 3 (1178 views) Re: Brake Pedal 2 The Floor Sign In Back brakes have a lot to do with pedal travel - the disc brakes set themselves. Back drum brakes need to be adjusted close but not dragging. If you didn't machine or replace drums or rotors they will feel soft until broken in. That's not the best way to do brakes. Also, what can happen is you pushed back the pistons in the calipers to make clearance for the new pads and when you pumped up the brakes to set them there would be several pumps before they were set. The seals in the master cylinder are older and they haven't traveled that far in the bore and what can happen is it's crusty in there and they go torn up. Also - did you allow master cylinder to run too low on fluid? If so it pushed air in and would need bleeding all brakes which is a good idea anyway. Even with all new parts new brakes don't always feel so great for a couple stops and are at there best after a couple hundred average miles of driving but should still stop well, T Guest Anonymous Poster Aug 28, 2007, 1:56 PM Post #3 of 3 (1175 views) Re: Brake Pedal 2 The Floor Sign In Thanks!! For the tip!! Im on the road again!   Automotive Repair     Auto Body Repair and Refinishing     Heating or AC Issues     Electrical and Wiring     Brake Systems     Car Stereo Repair Advice     General Discussions     Car Making Funny Noises     Engine Fault Codes     Engine Troubles     Exhaust Systems     Steering and Suspension     Transmission Troubles     Tricks of the Trade Automotive World     General Discussions     Antique Car Talk     Car Shows and Events     The Bargin Bin     Motor Vehicle Inspection     Car Care Tips     Traffic Tickets     Gasoline, Motor Oils, Concept Cars and Engines     Auto Insurance, Financing, Leases, Warranties Truck Repair     General Discussions     Truck Engine Repair     Truck Suspension Repair Motorcycle Repair     General Discussions     Motorcycle Engine Repair CarJunky     Open Posting     Board FAQ's     New Board Suggestions

Search this forum this category all forums for All words Any words Whole Phrase (options)

Privacy Sitemap