Main IndexAuto Repair Home Search Posts SEARCH
POSTS 		Who's Online WHO'S
ONLINE 		Log in LOG
IN




Automotive Repair
Car Troubleshooting Topics
  Car Troubleshooting
  Engine Troubleshooting
  Engine Fault Codes
  Electrical and Wiring
  Transmission Problems

Car Repair Topics
  Car Making Noises
  Car Stereo Repair
  Heating or AC Issues
  Motorcycles and ATVs
  Tricks of the Trade
  Truck Repair Advice

Site Options:   
  Login
  Sign up here!



Latest Forum Post
with_replies.gif image   Lukewarm Heat............
New antifreeze reverse flush heater core...

with_replies.gif image   multiple warning lights
2013 GMC Terrain 130,000 miles 4 cylinde...

with_replies.gif image   2014 Nissan Sentra Shaking
Car recently started shaking when accele...

no_replies.gif image   Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086
N/A

hot_with_replies.gif image   1989 toyota pickup 3.0 crank no start
I have a 1989 toyota pickup 3.0 crank no...

with_replies.gif image   Strut spring orientation and strut mount tension nut
2017 Nissan rogue awd 2.5 L Put in Monro...

with_replies.gif image   Transmission stuck in part, I have tried everything
So I'm working on my elderly fathers 201...

with_replies.gif image   2017 dodge journey LED headlights on/off randomly
Year of vehicle 2017 Make of vehicle dod...

with_replies.gif image   Kia Soul starter replacement issues!
Okay so my car is a 2010 Kia soul 2.0 en...

hot_with_replies.gif image   Please Help - Knock sound & engine fail
Hi all, Hoping to get some insight and ...




brake pads

Search for (search options)
 



leftuncheckd
Anonymous Poster
leftuncheckd@excite.com

Dec 3, 2007, 8:24 PM

Post #1 of 4 (2718 views)
brake pads Sign In
Have a 98 suzuki esteem--fr disc brakes
driver side front
uneven wear--inside pad worn normal on top half-almost no wear on the bottom. The outside pad shows normal wear both top and bottom halves.
Do I need to replace the caliper or bracket or will bleeding the line to it ? Or shim it ?


Tom Greenleaf
Ultimate Carjunky / Moderator
Tom Greenleaf profile image

Dec 4, 2007, 4:03 AM

Post #2 of 4 (2712 views)
Re: brake pads Sign In
Couldn't find a diagram of how this is designed. No matter. The caliper and or the bracket or the pads are jammed would be the likely cause. You should dismantle this and see what isn't working or sliding as it should to determine what is the jam up causing this. Did notice these are available as a loaded caliper and that should cover all the possibilities of the failure except the flex hose which shouldn't be able to cause this top to bottom uneven wear. If corroded and not just a broken item I would strongly consider doing both sides,

T



leftuncheckd
Anonymous Poster

Dec 4, 2007, 8:56 PM

Post #3 of 4 (2708 views)
Re: brake pads Sign In
Tom;
You were right. A closer inspection revealed that the caliper bent the cast metal pad backing causing the pad surface material to separate from the backing.
Replaced with an old pad I had saved from an old install, about the same wear as the outer pad. That should get me through until warmer weather, at which time I'll replace pads & rotors.
The defective pad was a Raybestos from Checker APs

Thanks


Tom Greenleaf
Ultimate Carjunky / Moderator
Tom Greenleaf profile image

Dec 5, 2007, 4:01 AM

Post #4 of 4 (2706 views)
Re: brake pads Sign In
What may have happened is the friction material separated first then when out of place the force bent the backing metal. That happens here usually on low mileage vehicles that are exposed to the salt used on the roads in Winter. The more expensive pads usually are more corrosion resistant. If that's a problem where you are just look at a couple different grades or brands of pads and rotors and at a glance you can see that some are plated or painted to resist that problem,

T






 
 
 






Search for (options) Privacy Sitemap