|
|
chickenhouse
Enthusiast
Jan 6, 2013, 3:29 PM
Post #1 of 41
(4729 views)
|
|
heater, 99 Malibu
|
Sign In
|
|
Is running great. Heater will not cooperate. Both hoses hot to core, just not getting the vacuum to the interior. Gray hose from throttle body base to the wiring harness goes around the back of brake booster and is included in the wiring harness is what I mean, goes to the cabin. I need a vacuum schematic of the vacuum lines for the heat-a/c. Took the line off the throttle body and put a vacuum plug on, smoothed the engine out dramatically. Tells me open vacuum line to cabin. Did I splain myself right?
(This post was edited by chickenhouse on Jan 6, 2013, 3:44 PM)
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jan 6, 2013, 3:33 PM
Post #2 of 41
(4722 views)
|
|
Re: hjeater, 99 Malibu
|
Sign In
|
|
That's because the temp actuator is is electric, not vacuum.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
chickenhouse
Enthusiast
Jan 6, 2013, 3:48 PM
Post #3 of 41
(4708 views)
|
|
Re: hjeater, 99 Malibu
|
Sign In
|
|
OK, the mode switch that chooses between a/c and heat has all vacuum lines behind it. The temp control has vacuum hoses and electric for the rheostat far as I can tell.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jan 6, 2013, 3:57 PM
Post #4 of 41
(4694 views)
|
|
Re: hjeater, 99 Malibu
|
Sign In
|
|
No, Mode control is vacuum. That is air direction only. The temp blend door is electric.
Temperature Actuator Replacement
REMOVAL PROCEDURE
- Remove the instrument panel compartment.
- Disconnect the harness connector.
- Remove the two screws and the actuator.
INSTALLATION PROCEDURE
- Position the actuator and install the screws.
- Connect the harness connector.
- Install the instrument panel compartment.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
chickenhouse
Enthusiast
Jan 6, 2013, 4:32 PM
Post #5 of 41
(4676 views)
|
|
Re: hjeater, 99 Malibu
|
Sign In
|
|
What time does it call for?
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jan 6, 2013, 4:53 PM
Post #6 of 41
(4666 views)
|
|
Re: hjeater, 99 Malibu
|
Sign In
|
|
.3 hr It's pretty easy
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
chickenhouse
Enthusiast
Jan 6, 2013, 5:04 PM
Post #7 of 41
(4659 views)
|
|
Re: hjeater, 99 Malibu
|
Sign In
|
|
So the instrument panel compartment is the glove box?
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jan 6, 2013, 5:05 PM
Post #8 of 41
(4655 views)
|
|
Re: hjeater, 99 Malibu
|
Sign In
|
|
Probably neither. You should be able to access it from under the dash on the p#$$enger side.
I don't know what is going on with the site. I typed that word correctly and that's what came out "passenger"
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
(This post was edited by Hammer Time on Jan 6, 2013, 5:07 PM)
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jan 6, 2013, 5:08 PM
Post #9 of 41
(4646 views)
|
|
Re: hjeater, 99 Malibu
|
Sign In
|
|
That's strange. That word showed correctly until I clicked on "post reply"
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
chickenhouse
Enthusiast
Jan 6, 2013, 5:27 PM
Post #10 of 41
(4628 views)
|
|
Re: hjeater, 99 Malibu
|
Sign In
|
|
Site is still a little weird.
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Jan 6, 2013, 5:28 PM
Post #11 of 41
(4626 views)
|
|
Re: hjeater, 99 Malibu
|
Sign In
|
|
I've see that on other words that contain the word a-s-s automatically switch. Who knows why? -- T
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jan 6, 2013, 5:32 PM
Post #12 of 41
(4615 views)
|
|
Re: hjeater, 99 Malibu
|
Sign In
|
|
Apparently it is seeing it as vulgarity.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Jan 6, 2013, 7:41 PM
Post #13 of 41
(4602 views)
|
|
Re: hjeater, 99 Malibu
|
Sign In
|
|
You guys gonna eat dinner with those mouths??????? Hope u wash em 1st..... .....
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jan 6, 2013, 7:43 PM
Post #14 of 41
(4595 views)
|
|
Re: hjeater, 99 Malibu
|
Sign In
|
|
I guess you know how the game turned out by now Brian
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Jan 6, 2013, 8:38 PM
Post #15 of 41
(4590 views)
|
|
Re: hjeater, 99 Malibu
|
Sign In
|
|
ahhhhhhhhh man.....that was impressive.....totally enjoyed it ( well except for the 1st quarter maybe)....I might even watch it again.......That was something they never would've be able to do before
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Jan 6, 2013, 9:01 PM
Post #16 of 41
(4579 views)
|
|
Re: hjeater, 99 Malibu
|
Sign In
|
|
I wish I could of been watching the game. I got to play carpenter today with my Uncle. My Grandfather passed away awhile back and left the house to his three kids. The drywall in the garage was coming down. Found out that there was some major termite damage. The termites had been exterminated when he was alive, but they had gotten up in to the trusses and ate the studs out in a seven foot section of wall between the garage and living room.
My Uncle decided to tackle the job of replacing the wood with me helping him. I don't know Sh!t about carpentry besides hammering nails in and cutting pieces of wood. He decided to lag bolt 2x6 to the eaten up pieces of truss, but didn't bring them out past the plates. I didn't say anything, but it doesn't look right to me. We built a new wall which turned out really nice though.
I noticed a mirror by the sink in the garage that looked like the frame was rotted. Took the mirror off and termites had eaten the paper off the back, so that means they had gotten into the back wall of the garage too. I personally think it is too much for us to tackle. My Uncle told me not to say anything to my Mom or Aunt. I thought, bullSh!t, so I told them anyway and recommended to have a professional come out and assess the damage. I think it is going to need a whole lot of work, which I really don't want to get involved in.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Jan 6, 2013, 9:03 PM)
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Jan 6, 2013, 9:24 PM
Post #17 of 41
(4572 views)
|
|
Re: hjeater, 99 Malibu
|
Sign In
|
|
I would definitely take my Sunday over that....Man...that's a lot of work....
For what ever reason......me & wood just don't seem to get along. It's always lopesided or too short....I'll do the little stuff, but nothing big like that....
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Jan 6, 2013, 9:35 PM
Post #18 of 41
(4568 views)
|
|
Re: hjeater, 99 Malibu
|
Sign In
|
|
I'm pretty good with baseboard, but when it comes to framing, that ain't my thing. When it comes to trusses that support the roof, that seems like it should be left to a pro. I don't want to be crawling around in the attic and falling through the ceiling with half the sheeting and shingling coming down with me...lol.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
|
chickenhouse
Enthusiast
Jan 11, 2013, 3:00 PM
Post #19 of 41
(4526 views)
|
|
Re: heater, 99 Malibu
|
Sign In
|
|
OK, back to the still unresolved heater problem. The actuator appears to be working. I took it off the heater housing and operating the heat control, the actuator moves, just like a bar b que spit would fit in it. Here's a part I don't get. Why does it bolt up to the housing and connect to a square on the housing that is designed to not move? It fits on the square and screws down, move the temp cont. and watch it move but there is nothing for it to move. I think I need a pic of the heater housing blow up.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jan 11, 2013, 4:05 PM
Post #20 of 41
(4521 views)
|
|
Re: heater, 99 Malibu
|
Sign In
|
|
That connects to the shaft of the blend door so it sounds like you have bigger problems with a broken blend door.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
chickenhouse
Enthusiast
Jan 11, 2013, 4:23 PM
Post #21 of 41
(4514 views)
|
|
Re: heater, 99 Malibu
|
Sign In
|
|
The outside of the actuator, the side you can see while bolted up has what looks like notches in it to spin a control rod but there were no parts found when I took it apart.
(This post was edited by chickenhouse on Jan 11, 2013, 4:37 PM)
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jan 11, 2013, 4:39 PM
Post #22 of 41
(4508 views)
|
|
Re: heater, 99 Malibu
|
Sign In
|
|
There should be a foot that slides over the shaft on the other side of the actuator.
This may not be your exact actuator but you get the idea.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
chickenhouse
Enthusiast
Jan 11, 2013, 5:53 PM
Post #23 of 41
(4503 views)
|
|
Re: heater, 99 Malibu
|
Sign In
|
|
Looks like what I have, the side shown screws to heater box. Other side has nothing attached to it, just a hole that something could be inserted in but nothing there or nothing found under the dash.
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Jan 12, 2013, 12:24 AM
Post #24 of 41
(4486 views)
|
|
Re: heater, 99 Malibu
|
Sign In
|
|
CH - Are you in trouble missing some parts? I can try at a neat local place to me for "stuff" that you just won't find new for things like that. Place is open picking for cars over 10 +/- years old and great for dinky dumb dash and HVAC stuff, clips, rods all that crap. Weather here a maybe for a another several days then all bets off. They get buried in snow then mud later so it's impossible for a while.
I'll go look for the whole a s s e m b l y for this car if you want. That place will let me - others just pluck away and take just what you need. Just a couple miles away so if I didn't have the tools with me it's easy enough to go back and forth for exact tools needed. Lemme know if in trouble. Only a maybe that an operable unit is there.
BTW - For U junkyard dogs (have been thru necessity for ages) with the pick your own places for electrical crap, bring a couple 9v household batteries (put together in series you get 18v) and jumper clips and you can test out little motors and things!
 Tom
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jan 12, 2013, 4:22 AM
Post #25 of 41
(4480 views)
|
|
Re: heater, 99 Malibu
|
Sign In
|
|
If that blend door is broken, it's not the part you have to be concerned about. It's the labor it's going to take to access the door itself.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
1989 toyota pickup 3.0 crank no start
Please Help - Knock sound & engine fail
1
