|
|
fr8erdawg
Novice
Nov 16, 2009, 1:27 PM
Post #1 of 15
(2062 views)
|
Just replaced heater core on 99 merc grand marq due to leakage now i have no heat. blower works fine in all positions just blows cool air. a/c works normal. tried swapping heater core hoses just in case but no help.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Nov 16, 2009, 1:53 PM
Post #2 of 15
(2041 views)
|
With the engine at full operating temp, locate the 2 heater hoses where they go into the firewall and feel them to see if they are both hot to the touch.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
fr8erdawg
Novice
Nov 16, 2009, 2:07 PM
Post #3 of 15
(2036 views)
|
both hoses are hot
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Nov 16, 2009, 2:10 PM
Post #4 of 15
(2032 views)
|
In that case you problems are not coolant related.
The heat in that vehicle is controlled by a blend door that regulates heated air flow. it is operated by an electric motor/actuator. The problem can be that the actuator is stripped or inoperative or the door itself could be damaged. This is what needs to be determined by examining the actuator and see if it is responding to heat change commands or not.
Chances are they assembled the box incorrectly and the door is jammed or broken which means it all has to come apart again.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
way2old
Veteran
/ Moderator
Nov 16, 2009, 5:14 PM
Post #5 of 15
(2022 views)
|
Or, hopefully, it was not plugged in. Lots easier.
Being way2old is why I need help from younger minds
|
|
| |
|
|
fr8erdawg
Novice
Nov 17, 2009, 8:28 AM
Post #6 of 15
(2015 views)
|
Thanks for the help. You were right the blend door actuautor does not move. When I disconnect the electric actuator I can manually move the door and get hot air. Thank goodness I did not have to remove the whole box again just the actuator. The dash is getting pretty easy to remove now that its been off several times. Again thanks for all your help.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Nov 17, 2009, 8:46 AM
Post #7 of 15
(2010 views)
|
No problem. Thanks for posting back.
Make sure the end of the pivot rod where the actuator connects is not damaged also.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
fr8erdawg
Novice
Nov 18, 2009, 11:05 AM
Post #8 of 15
(1994 views)
|
replaced actuator and still no movement. Mayby electrical wire broke? Door moves fine manually.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Nov 18, 2009, 11:12 AM
Post #9 of 15
(1990 views)
|
Did you actually look at the center of the actuator to see if it was turning.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
fr8erdawg
Novice
Nov 18, 2009, 11:21 AM
Post #10 of 15
(1986 views)
|
Yes. The arm does not move no matter what position the heat controller is put in.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Nov 18, 2009, 11:32 AM
Post #11 of 15
(1981 views)
|
I'm not talking about the arm. Take the actuator off and look at the center while moving the temp knob. It'd possible for the actuator to work but not move the door.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
fr8erdawg
Novice
Nov 18, 2009, 11:36 AM
Post #12 of 15
(1977 views)
|
Tried both. Holding the actuator with nothing connected except the connector it does not move no matter the heat position.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Nov 18, 2009, 11:40 AM
Post #13 of 15
(1973 views)
|
Check your fuses. You could have a bad control hear but it doesn't make sense for the situation. Make sure the control head is plugged in.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
fr8erdawg
Novice
Nov 18, 2009, 11:54 AM
Post #14 of 15
(1970 views)
|
Is there a fuse or something simple before I start tearing wire bundles apart?
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Nov 18, 2009, 12:19 PM
Post #15 of 15
(1970 views)
|
There is no reason to tear wire bundles apart, Of course, check your fuses using a test light.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
Lukewarm Heat............
Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086
1989 toyota pickup 3.0 crank no start
