|
|
1991 s10 c steering column swap now won’t go into first
|
|
|
| |
|
|
Newuser08
Novice
Jun 17, 2023, 7:53 PM
Post #1 of 9
(3136 views)
|
|
1991 s10 c steering column swap now won’t go into first
|
Sign In
|
|
I have a manual 1991 s10 I just bought a week ago, had the loose steering wheel, so I just swapped the column from an 89 blazer since I could get one for free. The blazer was an automatic, and I don’t know if this has to do with it. It shifted fine before, then once I changed it out, the clutch doesn’t engage. I don’t know if it’s just a coincidence that it happened at the same time, but if I start it in first with clutch all the way in, it will jump and stall like I lifted the clutch. It will also grind if I try to put it in reverse.
(This post was edited by Newuser08 on Jun 17, 2023, 7:54 PM)
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Jun 18, 2023, 2:03 AM
Post #2 of 9
(3099 views)
|
|
Re: 1991 s10 c steering column swap now won’t go into first
|
Sign In
|
|
I don't thing column of an automatic is compatible all the way thru firewall?
Clutch pivot hardware is not "disengaging" clutch apparently, not hooked up at all needs YOU to look hard at the two.
Time to do that was with both outside, see what is or isn't the same, welded, bolted or what.
IDK, S-10 dash was used in assorted "rest of thing vehicles" PU trucks, Blazer I forget but think plain 2WD perhaps one with floor shift vs column shift has to matter.
Answer will be fix (go surfing for parts) or exact right one.
Good news is these are popular to play with and alter, lower or raise whole body bet stuff is pre-made for about anything?
Tom
Tom
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 18, 2023, 4:03 AM
Post #3 of 9
(3090 views)
|
|
Re: 1991 s10 c steering column swap now won’t go into first
|
Sign In
|
|
Have you checked the clutch fluid level?
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Newuser08
Novice
Jun 18, 2023, 6:40 AM
Post #4 of 9
(3077 views)
|
|
Re: 1991 s10 c steering column swap now won’t go into first
|
Sign In
|
|
Old forums on the internet I had found say it is, and I had compared both parts prior, and the only difference was the automatic linkage going through the fire wall.
|
|
| |
|
|
Newuser08
Novice
Jun 18, 2023, 6:41 AM
Post #5 of 9
(3076 views)
|
|
Re: 1991 s10 c steering column swap now won’t go into first
|
Sign In
|
|
Yes, the fluid level is good, and there are no leaks when pushing on clutch
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 18, 2023, 6:44 AM
Post #6 of 9
(3072 views)
|
|
Re: 1991 s10 c steering column swap now won’t go into first
|
Sign In
|
|
If it hasn't lost any fluid then the problem has to be a bad clutch master.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Jun 18, 2023, 7:11 AM
Post #7 of 9
(3063 views)
|
|
Re: 1991 s10 c steering column swap now won’t go into first
|
Sign In
|
|
So.......with helper watch it move underhood while pushing down. If hydraulic (IDK none known to me) layout requires "free-play" > a finger push area, then resistance is real pushing. Note a working one that area is reduced on most or self wears out clutches when accelerating or under load,
T
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 18, 2023, 7:17 AM
Post #8 of 9
(3059 views)
|
|
Re: 1991 s10 c steering column swap now won’t go into first
|
Sign In
|
|
There is nothing to see on this vehicle. All movement occurs inside an enclosed bellhousing.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Jun 18, 2023, 8:31 AM
Post #9 of 9
(3044 views)
|
|
Re: 1991 s10 c steering column swap now won’t go into first
|
Sign In
|
|
OK - still it's just not disengaging. IDK in swapping column if involving removal of pivot went wrong. If pushrod too short to master because of that, that's it. If a bushing was used how it's pedal is held if lost.
IDK, all I owned or drove would "zip" for reverse or stop shafts by putting in another gear first quickly wouldn't. Reverse isn't synchro in ones (any make) is tell-tale of a clutch engaged or IDK warped shouldn't be from this.
Go back to what was done something went wrong didn't catch attention,
Tom
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
Drive Shaft Repair
2006 Toyoto Camry XLE Driver Side Electric Window Trouble
Grounding Cable, 2017 Jeep Renegade Trailhawk
equipment
Howdy
