|
|
Chefbb
Novice
Jun 17, 2017, 12:07 PM
Post #1 of 13
(1652 views)
|
I'm wondering if a mustang t5 tranny has the same bolt pattern as the jeep t5. Any and all help is greatly appreciated. I have a 79 cj7 and the transmission is a 4x4 t5. I'm not concerned about the 4 wheel drive right now. Just need to get back on the road. I've heard the mustang transmission is better than jeep so just curious if that's the way to go.
(This post was edited by Chefbb on Jun 17, 2017, 12:23 PM)
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 17, 2017, 2:23 PM
Post #2 of 13
(1633 views)
|
Not concerned about the 4 wheel drive?
You can't put a 2WD trans in a 4WD truck.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Chefbb
Novice
Jun 17, 2017, 4:02 PM
Post #3 of 13
(1624 views)
|
Even if i don't connect the front drive shaft? If i remove the front drive shaft completely it should work wouldn't it?
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 17, 2017, 4:14 PM
Post #4 of 13
(1620 views)
|
No, they are entirely different. You have a transfer case attached to the transmission, right?
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Chefbb
Novice
Jun 17, 2017, 4:25 PM
Post #5 of 13
(1613 views)
|
I do yes. Just having any impossible time finding a transmission. It's a borg warner t5. Can't find them anywhere unless i want to spend over 2000 bucks.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 17, 2017, 4:28 PM
Post #6 of 13
(1607 views)
|
It is what it is.
They cost that much for a reason. The seller knows how rare they are.
Can't you have yours rebuilt?
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Jun 17, 2017, 4:48 PM
Post #7 of 13
(1601 views)
|
This was when AMC (American Motors Corporation) was building "Jeeps and more" even the "CJ series." I've seen OE Audi engines in assorted AMC products so no surprises. Cost that much not surprised either,
T
|
|
| |
|
|
Chefbb
Novice
Jun 17, 2017, 5:08 PM
Post #8 of 13
(1593 views)
|
Yup. That's the issue I'm having. Rebuild would cost the same so guess I'm screwed lol.
|
|
| |
|
|
Chefbb
Novice
Jun 18, 2017, 5:10 PM
Post #9 of 13
(1568 views)
|
Found a t4. Will i need new drive shafts?
|
|
| |
|
|
Tom Greenleaf
Ultimate Carjunky
/ Moderator
Jun 18, 2017, 6:54 PM
Post #10 of 13
(1561 views)
|
Gary is site's designated trans specialist may be by.
#1 issue is and I love these things for some nutty reason is it's an AMC. Company was struggling bad for its life only Jeep division holding it together at all. They are wildly known for fitting in parts from whatever was available cheap no doubt new to roll off vehicles. This era you might have to bring old parts in and match them up as most everything was made by another motor company U-joints you matched up at a counter so can't say about driveshafts - match them up too I'm sure.
Now at age you probably don't know if whole assemblies are different somewhere along the way but fit.
To me - these were the last real chassis of a Civilian Jeep (hence named CJ) with some stuff still left over from WWII especially steering geometry needed a sense of humor.
It can't be just me you had to match stuff up with AMC's later vehicles and not a clue how you do that without parts in front of you?
T
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Jun 19, 2017, 8:27 PM
Post #11 of 13
(1546 views)
|
I'm not sure of your mechanical ability but if you aren't planning on doing anything with the tranny that went bad, tear it apart and check it out.....
Those aren't as complex as you may think they are....one good trick to know is chassis grease works great to hold little needle bearings in place on reassembly...
If you are planning on fixing it eventually then....you may want to think twice
(This post was edited by Sidom on Jun 19, 2017, 8:29 PM)
|
|
| |
|
|
Chefbb
Novice
Jun 20, 2017, 6:42 PM
Post #12 of 13
(1527 views)
|
Tore the tranny apart and a couple teeth missing on the main gear cluster. However i just bought t4 and Gina see if i can't get that in to drive. Will fix t5 whenever i get time off work and can find parts
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Jun 20, 2017, 6:45 PM
Post #13 of 13
(1525 views)
|
Good job......Man I wish i still had that kinda energy.....
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
Lukewarm Heat............
Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086
1989 toyota pickup 3.0 crank no start
