|
|
jacobmg1
New User
Aug 18, 2012, 12:09 PM
Post #1 of 6
(2068 views)
|
|
Dodge Caravan Leak help
|
Sign In
|
|
Hello, i am new here i hope you guys can take the time to help me out a little.
My problem: Alright so i bought a Caravan about a month ago with a leaky transmission, It is leaking from the metal plating Around the Drivers side Axle.
I attempted to fix befor by taking it all off and Siliconeing it. But now about 2 weeks later it is leaking again. I do not think that i sealed it right, they do not sell gaskets for them, so i was wondering if anyone have ever done one of these and if so how do i Silicone it right?
Heres a pic of the part, thank for the help
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Aug 18, 2012, 12:43 PM
Post #2 of 6
(2038 views)
|
|
Re: Dodge Caravan Leak help
|
Sign In
|
|
Are you sure it's the gasket leaking and not the seal around the axle?
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
jacobmg1
New User
Aug 18, 2012, 1:03 PM
Post #3 of 6
(2025 views)
|
|
Re: Dodge Caravan Leak help
|
Sign In
|
|
well it leaking where the bolt holes are on that thing, and from the buttom, so i would assume that the silicone isnt on there correctly. Right?
|
|
| |
|
|
Trans50
New User
Aug 18, 2012, 1:26 PM
Post #4 of 6
(2018 views)
|
|
Re: Dodge Caravan Leak help
|
Sign In
|
|
To seal this part of the transmission, you must thorughly clean the housing that you are displaying and the area of the transmission that it bolts to. Be sure to use a pick to clean anything that is in the thread holes. Then set the housing on a table with the flat bolt hole surface facing down. using a tube of clear silicone, run a bead of silicone about pencil thick around the complete circular base of the housing approx. one inch above the flange. DO NOT put any silicone on the transmission surface. This is not necessary. When placing the housing back in the trans, make sure the bolt holes are aligned with the holes in the housing. After it is pushed into place, take a clean straight pick and remove all excess silicone from the thread holes before installing any bolts. Any excess silicone that squeezes out from the outside perimeter of the housing should not be touched or cleaned. Let it dry just as it is.
|
|
| |
|
|
jacobmg1
New User
Aug 18, 2012, 1:28 PM
Post #5 of 6
(2017 views)
|
|
Re: Dodge Caravan Leak help
|
Sign In
|
|
Thanks i'm going to do it just as you said, Last time i put silicone all over the thing. So i'm going to try the pencil size all around the edge like you said. thank you
|
|
| |
|
|
Trans50
New User
Aug 18, 2012, 1:36 PM
Post #6 of 6
(2011 views)
|
|
Re: Dodge Caravan Leak help
|
Sign In
|
|
You also may want to look at the bearing race that is pressed into the housing. If the surface where the bearing rides is rough, that would be a sign of the bering itself being bad, and that also would cause a leak. However, if the bearing is bad enough to leak, you would surely hear a noise when driving.
Thanks
Neil
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
Lukewarm Heat............
Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086
1989 toyota pickup 3.0 crank no start
