|
|
|
Transmission won't engage
|
|
|
| |
|
|
Hfriesen
Novice
Jan 23, 2008, 2:04 AM
Post #1 of 14
(6258 views)
|
|
Transmission won't engage
|
Sign In
|
|
My daughters 91 Topaz made a loud bang then coasted to a stop. The motor ran fine but when shifted into any gear it just made a faint whirring sound. I thought it might be the drive axel so I raised the car to test it. The right front wheel could not be rotated with the car in park but would turn in all other gears so I don't think it's the axle. The axle feels solid and has not pulled out of the tranny. Any suggestions other than replacing the transmission?
|
|
| |
|
|
dave284
Enthusiast
Jan 23, 2008, 12:07 PM
Post #2 of 14
(6250 views)
|
|
Re: Transmission won't engage
|
Sign In
|
|
The info you gave sound like torque converter busted but it still could be the trans, won't know until converter is remove for inspection. 
|
|
| |
|
|
Hfriesen
Novice
Jan 26, 2008, 1:43 PM
Post #3 of 14
(6237 views)
|
|
Re: Transmission won't engage
|
Sign In
|
|
I have the transmission out. How do I test the torque converter?
|
|
| |
|
|
dave284
Enthusiast
Jan 26, 2008, 10:52 PM
Post #4 of 14
(6230 views)
|
|
Re: Transmission won't engage
|
Sign In
|
|
Drain what you can, look inside at where the splines line up with the main shaft ,when draining the converter check for metal particals in the fluid too. What you are looking for is the signs of a strip gear inside the conv. Do this and post your findings. 
|
|
| |
|
|
Hfriesen
Novice
Jan 27, 2008, 1:14 PM
Post #5 of 14
(6225 views)
|
|
Re: Transmission won't engage
|
Sign In
|
|
The oil is clean. I can see inside both the transmission and the converter. The bearing slides up and down in the transmission and nothing appears out of place in the converter. The long square shaft comes out ok. When you put them back you need to wiggle the bearing a bit inthe tran so it goes all the way in and the move the converter a bit so it seats. Thats all I can see there and no sediment in the oil.
|
|
| |
|
|
dave284
Enthusiast
Jan 28, 2008, 8:56 AM
Post #6 of 14
(6216 views)
|
|
Re: Transmission won't engage
|
Sign In
|
|
This is an automatic trans right?
|
|
| |
|
|
Hfriesen
Novice
Jan 28, 2008, 11:19 AM
Post #7 of 14
(6212 views)
|
|
Re: Transmission won't engage
|
Sign In
|
|
Yes, automatoc.
|
|
| |
|
|
Hfriesen
Novice
Jan 28, 2008, 12:08 PM
Post #8 of 14
(6209 views)
|
|
Re: Transmission won't engage
|
Sign In
|
|
I'm having a bit of trouble posting a picture so I will try again.
|
|
Attachments:
|
Topaz 0015.jpg
(153 KB)
|
|
| |
|
|
dave284
Enthusiast
Jan 28, 2008, 3:28 PM
Post #9 of 14
(6201 views)
|
|
Re: Transmission won't engage
|
Sign In
|
|
I saw the picture, going on of what you told me, other than replacing trans I would take the converter to trans shop and have a service man check it out.
|
|
| |
|
|
Hfriesen
Novice
Jan 31, 2008, 12:47 AM
Post #10 of 14
(6189 views)
|
|
Re: Transmission won't engage
|
Sign In
|
|
I took the transmission apart because I couldn't find any filings and really wanted to know what went wrong. I'll post some pics but deep inside after you remove everything that you can there was one very seriously stripped gear. my daughter said it made a bang so this must have failed in a catastrophic manner. Well it's fubar anyway.
(This post was edited by Hfriesen on Jan 31, 2008, 1:11 AM)
|
|
Attachments:
|
Jan 30 012.jpg
(103 KB)
|
|
|
Jan 30 011.jpg
(148 KB)
|
|
|
Jan 30 010.jpg
(134 KB)
|
|
| |
|
|
dave284
Enthusiast
Jan 31, 2008, 7:22 AM
Post #11 of 14
(6176 views)
|
|
Re: Transmission won't engage
|
Sign In
|
|
The bang was caused by the stripping of the splines all at once. Thats the way inside the converters look when they go out with a bang, but you now know the cause. Just remember to have the converter cleaned out /flushed before installing it in next trans, and the oil cooler too. good luck.
|
|
| |
|
|
Hfriesen
Novice
Feb 10, 2008, 1:49 PM
Post #12 of 14
(6134 views)
|
|
Re: Transmission won't engage
|
Sign In
|
|
Ok so I changed transmissions as carefully as I could. Flushed lines, did all the right torques and have the car back on the road. It seems to idle much faster now. I checked to see if I had inadvertently disconnected any vacuum lines but can't find any. If you put the car in gear it starts to drive. On some other car when some of the the vacuum lines are disconnected they speed up. I didn't readjust anything but this job requires a whole lot o messing around under the hood.
|
|
Attachments:
|
almost there.jpg
(159 KB)
|
|
|
back in.jpg
(200 KB)
|
|
|
Removed air filter.jpg
(159 KB)
|
|
| |
|
|
dave284
Enthusiast
Feb 10, 2008, 8:38 PM
Post #13 of 14
(6121 views)
|
|
Re: Transmission won't engage
|
Sign In
|
|
Ok the problem now is idle is too high, to check for vacumm leaks ,spray WD-40/ or carb cleaner anywhere theres a vac -line that you might have bumped also recheck all eletrical connections ! post back.
|
|
| |
|
|
dave284
Enthusiast
Feb 11, 2008, 7:57 AM
Post #14 of 14
(6117 views)
|
|
Re: Transmission won't engage
|
Sign In
|
|
the trans modulator could be bad .
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
+27730066655 HOW TO JOIN ILLUMINATI AND GET RICH IN JOHANNESBURG SOUTH AFRICA CONTACT PROF AAFA
1989 toyota pickup 3.0 crank no start
Strut spring orientation and strut mount tension nut
