|
|
|
electronic shift transmission help
|
|
|
| |
|
|
mtgeorge741
User
Nov 17, 2012, 1:31 PM
Post #1 of 14
(2028 views)
|
electronic shift transmission help
|
Sign In
|
|
i have a 1996 gmc jimmy with 4.3l engine and the transmission is an electronic shift transmission. think the 4L60. 123k miles. there is delayed shifting going on. it's acting like it doesn't want to grab the higher gear. there is a slight delay in when putting it into reverse. thinking maybe some sort of sensor on or in the transmission but don't know which one. need help asap
|
|
| |
|
|
Racer 51
User
Nov 17, 2012, 1:43 PM
Post #2 of 14
(2010 views)
|
|
Re: electronic shift transmission help
|
Sign In
|
|
I don't know the TSB # (Technical Service Bulletin) but I know there are TSB'S out. Check with a dealer for the TSB'S. Post any error codes that are set so they can be seen.
|
|
| |
|
|
mtgeorge741
User
Nov 17, 2012, 1:56 PM
Post #3 of 14
(2003 views)
|
|
Re: electronic shift transmission help
|
Sign In
|
|
that doesn't help
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Nov 17, 2012, 3:59 PM
Post #4 of 14
(1979 views)
|
|
Re: electronic shift transmission help
|
Sign In
|
|
How is the fluid level and fluid condition?
Reverse is all mechanical and not computer controlled. If you have a delay going into reverse, there is a pressure problem inside the transmission. You'll have to connect a transmission pressure gauge up and do some line pressure checks.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
|
mtgeorge741
User
Nov 17, 2012, 7:27 PM
Post #5 of 14
(1968 views)
|
|
Re: electronic shift transmission help
|
Sign In
|
|
condition is good. level is lower than it was n white smoke from exhaust consistant with tranny fluid burning but dont see any lines as should between the two. i don't see the shift linkage, nothing on the transmission. just a wire going to a large sensor on the side. dont see a kickback, a modulator, nothing. there are no vacuum lines going to the transmission
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Nov 17, 2012, 7:44 PM
Post #6 of 14
(1967 views)
|
|
Re: electronic shift transmission help
|
Sign In
|
|
The transmission line pressure is controlled by an electrical solenoid called a PCS (pressure control solenoid), so there is no throttle valve cable or vacuum modulator. Can't think of any reason the engine would be burning transmission fluid. Is the white smoke coming out from the end of the exhaust pipe or is it coming from underneath the vehicle?
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
|
mtgeorge741
User
Nov 17, 2012, 7:53 PM
Post #7 of 14
(1961 views)
|
|
Re: electronic shift transmission help
|
Sign In
|
|
and where is that located? the exhaust pipe
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Nov 17, 2012, 8:02 PM
Post #8 of 14
(1960 views)
|
|
Re: electronic shift transmission help
|
Sign In
|
|
The end of the exhaust pipe is at the back of vehicle. Unless the muffler fell off...
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
|
mtgeorge741
User
Nov 17, 2012, 8:05 PM
Post #9 of 14
(1958 views)
|
|
Re: electronic shift transmission help
|
Sign In
|
|
i meant the pcs. i know where the exhaust is.
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Nov 17, 2012, 8:11 PM
Post #10 of 14
(1952 views)
|
|
Re: electronic shift transmission help
|
Sign In
|
|
The PCS is on the valve body behind the transmission pan. PCS won't cause a loss of fluid though.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Nov 17, 2012, 8:15 PM)
|
|
| |
|
|
mtgeorge741
User
Nov 17, 2012, 9:16 PM
Post #11 of 14
(1946 views)
|
|
Re: electronic shift transmission help
|
Sign In
|
|
is there wires going to it? is it grey in color?
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Nov 17, 2012, 9:23 PM
Post #12 of 14
(1945 views)
|
|
Re: electronic shift transmission help
|
Sign In
|
|
The wires to the PCS solenoid come into the transmission at the electrical plug you saw on the side of the transmission. The PCS gets power and ground on the light blue/white and red/black wires at the plug.
The electrical harness inside transmission that comes from the other side of the plug that goes to the solenoid itself use a light blue and a purple wire.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
|
mtgeorge741
User
Nov 18, 2012, 7:44 AM
Post #13 of 14
(1931 views)
|
|
Re: electronic shift transmission help
|
Sign In
|
|
okay. you'd think that would throw an engine code. when i ran the codes before, nothing showed up about the transmission. just oxygen sensor no circuit, another oxygen sensor code, multiple misfire, cylinder 4 misfire. how do i adjust the shift linkage?
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Nov 18, 2012, 8:56 AM
Post #14 of 14
(1926 views)
|
|
Re: electronic shift transmission help
|
Sign In
|
|
If the engine has misfires and or problems, you need to correct those first. A bad running engine is going to affect the operation of the transmission. Once you have the engine problem sorted out and you find you still have a problem with the transmission is when you need to take it into a transmission shop and have them take a look at it. They might do some pressure tests and see what line pressure is at when the reverse delay is occurring. It would also be important to find out where the transmission fluid is leaking from.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Nov 18, 2012, 9:01 AM)
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
1989 toyota pickup 3.0 crank no start
Please Help - Knock sound & engine fail
