|
|
Spicemaster
User
Jun 14, 2017, 1:29 PM
Post #1 of 26
(3654 views)
|
Hi guys...I am replacing the clutch in my 07 kia( 1.6 dohc) and i have a serious problem. I have removed everything from the tranny, took out the transaxle, and removed all the bolts.... But the housing will not come loose! I've worked a couple of screwdrivers in where I can, and it will separate a litte on the underside, but it is almost like it's still bolted at the top. Any hints would be greatly appreciated. This car is driving me.to the brink of insanity!
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Jun 14, 2017, 2:05 PM
Post #2 of 26
(3650 views)
|
|
Re: help! I'm stuck!
|
Sign In
|
|
Hang tight before you pry anymore.....
Not positive on the Kia's but I know the Hyundias have dual mass flywheel that you can damage if you pry to hard.......On the Hyundia's you need to remove the clutch fork off the trans or it won't come out.......If you pry too hard you will trash the flywheel...
When you "move" the tranny back if it looks like the fork is pulling end, then more than likely you will have to remove it....
What type of Kia is it?
(This post was edited by Sidom on Jun 14, 2017, 2:14 PM)
|
|
| |
|
|
Spicemaster
User
Jun 14, 2017, 2:58 PM
Post #3 of 26
(3629 views)
|
|
Re: help! I'm stuck!
|
Sign In
|
|
It's a kia rio... I'll try to move the fork and let you know
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 14, 2017, 3:09 PM
Post #4 of 26
(3625 views)
|
|
Re: help! I'm stuck!
|
Sign In
|
|
Make sure you actually have all the bolts out. There may be some coming from the other direction.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Jun 14, 2017, 3:27 PM
Post #5 of 26
(3619 views)
|
|
Re: help! I'm stuck!
|
Sign In
|
|
I didn't see anything out of the ordinary......Like Ht said......Double check around the bellhousing to make sure you didn't miss any bolts.....some come thru at the other way at the bottom...Usually in the place that's the worst to get to....
|
|
| |
|
|
Spicemaster
User
Jun 14, 2017, 3:43 PM
Post #6 of 26
(3613 views)
|
|
Re: help! I'm stuck!
|
Sign In
|
|
Actually, the bell housing is in 2 parts...which I found out the hard way... And I only have to take out the front half of it... I found a little info through a chilton manual, but it was a brief diagram; not enough info to do the whole job step by step
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Jun 14, 2017, 4:32 PM
Post #7 of 26
(3597 views)
|
|
Re: help! I'm stuck!
|
Sign In
|
|
Well I haven't had the pleasure of doing that model so I'm just going off what I see in my data base and it doesn't sound like what you are working on.
The 2 piece bellhousing sounds a bit odd...
Check the 10th digit of your vin......should be a 7
What I have is showing the transaxle & bellhousing as 1 piece....
If someone else has something different, hopefully they'll post it
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 14, 2017, 5:41 PM
Post #8 of 26
(3591 views)
|
|
Re: help! I'm stuck!
|
Sign In
|
|
I'm not sure what you're attempting to do here but in order to remove the transmission on this car you have to support the engine from above and remove the sub-frame below.
There is no second bellhousing, just where it separates from the engine.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
(This post was edited by Hammer Time on Jun 14, 2017, 5:42 PM)
|
|
| |
|
|
Spicemaster
User
Jun 19, 2017, 8:06 AM
Post #9 of 26
(3542 views)
|
|
Re: help! I'm stuck!
|
Sign In
|
|
Am i seeing this right? Am i going to have to remove the entire steering transaxle to get the subframe off? Or can i unbolt from the subframe and let it hang?
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 19, 2017, 12:34 PM
Post #10 of 26
(3518 views)
|
|
Re: help! I'm stuck!
|
Sign In
|
|
No, the subframe has to be removed completely and the engine supported from above.
This is not unusual these days.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Spicemaster
User
Jun 19, 2017, 12:39 PM
Post #11 of 26
(3514 views)
|
|
Re: help! I'm stuck!
|
Sign In
|
|
God I miss the days of good old cold rolled Detroit steel!
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 19, 2017, 12:46 PM
Post #12 of 26
(3510 views)
|
|
Re: help! I'm stuck!
|
Sign In
|
|
Front wheel drive is a whole different animal.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Spicemaster
User
Jun 19, 2017, 8:26 PM
Post #14 of 26
(3494 views)
|
|
Re: help! I'm stuck!
|
Sign In
|
|
I appreciate the heads up on the coupling...and I do have the engine supported from the top and a couple of bolts holding thr tranny until i can get a floor jack under it... Man, i have never had a car kick my ass like this!
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Jun 19, 2017, 8:38 PM
Post #15 of 26
(3488 views)
|
|
Re: help! I'm stuck!
|
Sign In
|
|
Yea the 1st fwd tranny can really be a PITA......After you do a few of them they aren't too bad.....On a lift, you can drop a subframe rather quickly.....I don't think I've ever done one on my back, so you definitely have my sympathy....
Personally I would never disconnect the coupler, on flat rate, time is money but I did see a few guys have their bungy cords come loose & stretch an SRS cable....
Also, once again, I'm sure you already did it....but pull the key out of the ign before you take the coupler off so the steering wheel doesn't turn....
|
|
| |
|
|
Spicemaster
User
Jun 25, 2017, 9:10 AM
Post #17 of 26
(3442 views)
|
|
Re: help! I'm stuck!
|
Sign In
|
|
So i have been trying to disconnect the steering axle with no luck...and taking a closer look, how difficult is it to just remove and replace the pinion assembly? It seems that if I disconnected that, I could drop the subframe no problem...any thoughts?
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 25, 2017, 9:17 AM
Post #18 of 26
(3436 views)
|
|
Re: help! I'm stuck!
|
Sign In
|
|
I don't know what you are calling a steering axle but yes, you can unbolt the rack from the sub-frame along with any line hold downs that may be attached to the frame also. Actually you have to leave the rack in the car as all the lines are attached to the engine.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Jun 25, 2017, 9:27 AM
Post #19 of 26
(3432 views)
|
|
Re: help! I'm stuck!
|
Sign In
|
|
That depends on the tech....There is always more than one way to get there.....I'm assuming you are talking about the steering gear/rack & pinion/rack.....Most rack's have 2 mountings to the frame, 2 outer tie rod ends, a steering coupler, 2 p/s hose and maybe some electrical connections....All these would need to be disconnected to remove the rack....That would be a lot more work & reinstalling p/s hoses on some racks can be a total PITA......Personally I would just take the 2 mounts & 1 TRE loose & hang the rack with 1 or 2 large zip ties and bungy cords.....For safety it would be better than you take the couple extra step we already talked about, including taking the key out of the ign.....
If you are talking about dropping the frame with the rack still mounted to it......That's another way to get there....I've seen guys do that....and even with a lift.....it's a pain to get the rack's coupler lined up with the steering column on reassembly and then you still have the hoses as well.......
Are you having trouble with the mountings?
|
|
| |
|
|
Spicemaster
User
Jun 25, 2017, 9:28 AM
Post #20 of 26
(3428 views)
|
|
Re: help! I'm stuck!
|
Sign In
|
|
Sorry, used the wrong term. Its the rack that i can't get off the subframe... It's bolted from the top and i can't reach the bolts to remove them; but it looks like if I disconnect the pinion assembly from the car, i can drop the subframe enough to move the tranny out enough to replace the clutch. What I am wondering is how hard it is to remove and replace the pinion assembly; it looks like it is just a rubber boot holding it with four connecting points
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 25, 2017, 9:32 AM
Post #21 of 26
(3422 views)
|
|
Re: help! I'm stuck!
|
Sign In
|
|
It has a tie rod at each end connected along with 2 hoses and the coupler. Your best bet would be as Sidom suggests and unbolt it from the frame and let it hang from the engine with the hoses connected.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Spicemaster
User
Jun 25, 2017, 10:36 AM
Post #22 of 26
(3416 views)
|
|
Re: help! I'm stuck!
|
Sign In
|
|
It has a shaft that has tie rods at eithr end, with a 90 that runs up into the body[ where I assume the pinion assembly is], no hoses... And two additional rods that connect to the suspension. The part that is keeping me from moving the tranny the 6 inches I need is what i am calling the pinion assembly...does that help? This was a bare-bones model...no power anything.
|
|
| |
|
|
Hammer Time
Ultimate Carjunky
/ Moderator
Jun 25, 2017, 10:42 AM
Post #23 of 26
(3412 views)
|
|
Re: help! I'm stuck!
|
Sign In
|
|
Of course it has hoses unless for some reason you don't have power steering and I doubt that.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We offer help in answering questions, clarifying things or giving advice but we are not a substitute for an on-site inspection by a professional.
|
|
| |
|
|
Spicemaster
User
Jun 25, 2017, 10:59 AM
Post #24 of 26
(3406 views)
|
|
Re: help! I'm stuck!
|
Sign In
|
|
No hoses...so is it safe to disconnect the pinion assembly? And more importantly will it go back together easily or is there a trick to it?
|
|
| |
|
|
Sidom
Veteran
/ Moderator
Jun 25, 2017, 12:14 PM
Post #25 of 26
(3399 views)
|
|
Re: help! I'm stuck!
|
Sign In
|
|
I don't see any electric steer options for this year or a manual rack....The "hoses" are steel lines at the the connections......with rubber in the middle. The rack also has complete steel lines on it for internal pressure transfer that don't come off, they are part of the assembly.....If you choose the route you are thinking about,....don't take off the wrong lines......This has a standard clamp (2 bolts) on the the R side and a solid 2 bolt mount on the left that mounts the rack to the frame.....Position the coupler pinch bolt in a spot you can easily remove, take the key out of the ign...Mark the steering coupler on the column with whiteout and remove....Now if you you loosen the rear sub frame bolts, you may be able to drop the frame enough to access the rack mounting bolts easier and remove.....obviously sercuring the rack so it can "hang" safely once the bolts are removed.....
If you choose the route you are thinking about....The coupler steps are the same.......The hoses are on the "tower" (top part) of the rack on the left side....Should be 18mm nuts.....Just know this....Those can be difficult to start sometimes and it is very easy to crossthread the nuts....never use a wrench to start those...and some use the same thread size for high and low pressure so be absolutely sure of which hoses goes to which port before you take them off....
Working on your back sux....I get it....So you decide on the best path...just understand the pitfalls of each route....I'm going off the top of my head but don't think I've forgotten anything....If I have, i'm sure one of the other guys will jump in
|
|
| |
|
| | |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
Lukewarm Heat............
Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086
1989 toyota pickup 3.0 crank no start
1
