|
|
waitaminute94
User
Aug 28, 2012, 12:54 PM
Post #1 of 11
(2777 views)
|
stick shift wobble
|
Sign In
|
|
1994 saturn SL1, 4 cyl., 1.9, 4D sedan, approx. 200,000 mi.
running smooth as a cucumber after sitting about year.
changed some basic things like pcv valve, air & oil filter, gas, battery charge.
I drove it for about 20-30 miles with no problems.
I parked it for two days, started right up. Engaged 1st gear, moved a couple feet and took my foot off the clutCH too fast, causing car to jerk to a stop. when I started it back up, my foot was on the clutch, but the stick shift just wobbled,
not able to engage any gear. Did a pin fall out or is it something serious.
HELP
[/reply]
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Aug 28, 2012, 1:05 PM
Post #2 of 11
(2767 views)
|
|
Re: stick shift wobble
|
Sign In
|
|
Usually what happens is a shift cable bushing falls apart and the cable comes of the gear shifter or the shift linkage. You'll have to inspect both ends of the cables to see what came off. Usually, you have to replace the cables.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Aug 28, 2012, 1:06 PM)
|
|
| |
|
|
waitaminute94
User
Aug 28, 2012, 1:29 PM
Post #3 of 11
(2755 views)
|
|
Re: stick shift wobble
|
Sign In
|
|
in referrence to the shifter under the rubber boot (on console) are the cables "under" the car or do I need to remove the console (or anything)?
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Aug 28, 2012, 4:05 PM
Post #4 of 11
(2735 views)
|
|
Re: stick shift wobble
|
Sign In
|
|
You can see one end of the cables at the transaxle. They run from underneath the center console and through the firewall to the transaxle. You have to remove the center console to get access to the cable ends at the shifter lever assembly.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Aug 28, 2012, 4:06 PM)
|
|
| |
|
|
waitaminute94
User
Aug 28, 2012, 11:25 PM
Post #5 of 11
(2716 views)
|
|
Re: stick shift wobble
|
Sign In
|
|
Thanks, I needed that.
time to get busy 
|
|
| |
|
|
waitaminute94
User
Aug 29, 2012, 8:03 AM
Post #6 of 11
(2705 views)
|
|
Re: stick shift wobble
|
Sign In
|
|
after getting access to the cables under the console and inspecting the cables on this end (which seem to be perfecly fine) it feels like the end of the cable (r.s.) is disconnected from the linkage of the shifter while moving the shifter with one hand and cable with the other hand. won't know unless shifter box is dismanteled (is that necessary? ) and could it be broken or is there some kind of pin or screw that needs to be replaced?
Thanks in advance
|
|
| |
|
|
kensoncustom
User
Aug 29, 2012, 8:31 AM
Post #7 of 11
(2700 views)
|
|
Re: stick shift wobble
|
Sign In
|
|
If both cables are hooked up, problem is most likely a broken selector shaft pin in transaxel.
look at top of trans where shift leavers are located if this cover is bolted on,you can remove cover replace roll pin in seletor shaft
|
|
| |
|
|
waitaminute94
User
Aug 29, 2012, 8:47 AM
Post #8 of 11
(2697 views)
|
|
Re: stick shift wobble
|
Sign In
|
|
thanks, I'll give it try
|
|
| |
|
|
waitaminute94
User
Aug 29, 2012, 1:28 PM
Post #9 of 11
(2689 views)
|
Re: stick shift wobble
|
Sign In
|
|
i completely forgot that saturns are relics now. and when i followed the instructions given me by the knowledgable mechanics in the forum, my problem was made crystal clear.
it was a worn out bushing (probably cost a penny to make) and I couldn't find it anywhere. SO, now I had to improvise.
Ingredients: quarter inch tubing X 1/2" to fit over the ball,
string wire wrapped around the connection about a hundred times to reassure that the ball dosen't fall out, then covered with Gorilla tape,with enough wiggle room to shift the gears. Done deal? OH, COST? NOTHING
Now, ask me what rock did I crawl from under? LOL
THANKS EVERYBOBY
|
|
| |
|
|
kensoncustom
User
Aug 29, 2012, 1:46 PM
Post #10 of 11
(2687 views)
|
|
Re: stick shift wobble
|
Sign In
|
|
good will most likely last a life time the bushings are molded in cable.
|
|
| |
|
|
nickwarner
Veteran
/ Moderator
Aug 29, 2012, 4:52 PM
Post #11 of 11
(2679 views)
|
|
Re: stick shift wobble
|
Sign In
|
|
MacGuyver would be proud.
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
Lukewarm Heat............
Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086
1989 toyota pickup 3.0 crank no start
