|
|
Mr.scotty
Enthusiast
May 15, 2011, 8:41 PM
Post #1 of 9
(2923 views)
|
Scope question
|
Sign In
|
|
I just bought a handheld one channel lab scope and had a question.
I always see two test probes on scopes ( I'm guessing one is for ground and one is for the signal wire) in all the autotive applications but mine only has one.
Is this a problem or will my scope work the same just not needing a ground?
My question is more pointed at Hammer time cause Tom greenleaf said he would know but anyone can chime in.
I'm new to scopes so any tips or info would be great!
Thanks
--------------------------------------------------------
Your only as good as your tools!
|
|
| |
|
|
zmame
Veteran
/ Moderator
Jun 27, 2011, 3:36 PM
Post #2 of 9
(2776 views)
|
|
Re: Scope question
|
Sign In
|
|
Just think of it as a positive and negitive on a multi-meter.
like when testing a ABS sensor use your sig lead on + output and COM on the - output of the sensor spin the tire by hand you can watch the scope patter.
you can do some reading on different wave patterns for diaging different things, injectors, coils, crank/cam sensors and etc..
If you can attach a low amp probe you can also do injector performances, fuel pump perfomance/condition and many other things.. that if your scope does amps and has fast enough response time. I use VantagePro scope at work amazing pice of equipment I actually bought my own.
|
|
| |
|
|
Mr.scotty
Enthusiast
Jun 27, 2011, 9:10 PM
Post #3 of 9
(2772 views)
|
|
Re: Scope question
|
Sign In
|
|
Right, but the thing i can't figure out is why my scope only has one test lead.
--------------------------------------------------------
Your only as good as your tools!
|
|
| |
|
|
zmame
Veteran
/ Moderator
Jun 28, 2011, 4:29 AM
Post #4 of 9
(2767 views)
|
|
Re: Scope question
|
Sign In
|
|
Post your spesific model here ill look it up.
(This post was edited by zmame on Jun 28, 2011, 4:30 AM)
|
|
| |
|
|
Mr.scotty
Enthusiast
Jun 28, 2011, 10:01 AM
Post #5 of 9
(2760 views)
|
|
Re: Scope question
|
Sign In
|
|
It's a velleman instruments model HPS10 personal oscilloscope
--------------------------------------------------------
Your only as good as your tools!
|
|
| |
|
|
zmame
Veteran
/ Moderator
Jun 28, 2011, 3:12 PM
Post #6 of 9
(2754 views)
|
|
Re: Scope question
|
Sign In
|
|
From what I read in the instruction manual online for that specific model you use the probe on + side,
exsample for wheel speed sensor..
set it to 5v DC
time devision to 30 seconds
probe set at 1x on the + side and tool should have a reading when you spin the wheel.
You may have to calibrate your scope too the process in the your instruction booklet.
|
|
| |
|
|
Mr.scotty
Enthusiast
Jun 28, 2011, 8:20 PM
Post #7 of 9
(2750 views)
|
|
Re: Scope question
|
Sign In
|
|
Ok, Do i use it on signal wires if the part has one (like a crank sensor)?
--------------------------------------------------------
Your only as good as your tools!
|
|
| |
|
|
zmame
Veteran
/ Moderator
Jun 29, 2011, 4:31 AM
Post #8 of 9
(2744 views)
|
|
Re: Scope question
|
Sign In
|
|
on + side (signal side).
|
|
| |
|
|
Mr.scotty
Enthusiast
Jun 29, 2011, 8:11 PM
Post #9 of 9
(2734 views)
|
|
Re: Scope question
|
Sign In
|
|
Got ya, Thanks again!
--------------------------------------------------------
Your only as good as your tools!
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
Lukewarm Heat............
Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086
1989 toyota pickup 3.0 crank no start
