Crankshaft pully bolt - General Discussions


	Auto Repair Home	SEARCH POSTS	WHO'S ONLINE	LOG IN

Automotive Repair

Car Troubleshooting Topics
  Car Troubleshooting
  Engine Troubleshooting
  Engine Fault Codes
  Electrical and Wiring
  Transmission Problems

Car Repair Topics
  Car Making Noises
  Car Stereo Repair
  Heating or AC Issues
  Motorcycles and ATVs
  Tricks of the Trade
  Truck Repair Advice

Site Options:
  Login
  Sign up here!

Latest Forum Post

+27730066655 HOW TO JOIN ILLUMINATI AND GET RICH IN JOHANNESBURG SOUTH AFRICA CONTACT PROF AAFA

+27730066655 HOW TO JOIN ILLUMINATI AND ...

1989 toyota pickup 3.0 crank no start

I have a 1989 toyota pickup 3.0 crank no...

Strut spring orientation and strut mount tension nut

2017 Nissan rogue awd 2.5 L Put in Monro...

Transmission stuck in part, I have tried everything

So I'm working on my elderly fathers 201...

2017 dodge journey LED headlights on/off randomly

Year of vehicle 2017 Make of vehicle dod...

Kia Soul starter replacement issues!

Okay so my car is a 2010 Kia soul 2.0 en...

Please Help - Knock sound & engine fail

Hi all, Hoping to get some insight and ...

multiple warning lights

2013 GMC Terrain 130,000 miles 4 cylinde...

03 alero no low speed blower

Good day everyone, I have a 2003 Olds a...

04 Chevy 2500hd tail light issues

Help!!! I have changed my combo switch...

Crankshaft pully bolt

Sign up here!

Search for (search options)

Auto Repair Home>> Automotive World>> General Discussions

nevadaghosttown
New User

Jan 16, 2010, 4:53 PM

Post #1 of 4 (2181 views)

Crankshaft pully bolt	Sign In

I have a 1987 Toyota 4Runner 2.4L Turbo with automatic trans( hate them). I just replaced the crankshaft seal belts, waterpump. My problem how to keep the crank from turning while torqueing the bolt. The trans inspection plate you have to remove the tranny to remove it. I have the belts tight for now and have used sockets with other ratchetts on power steering pully bolt and alt pully bolt. Im out of ideas please help. Also no air tools.

Tom Greenleaf
Ultimate Carjunky / Moderator
Tom Greenleaf profile image

Jan 16, 2010, 5:26 PM

Post #2 of 4 (2174 views)

Re: Crankshaft pully bolt	Sign In

Will probably take a helper but you should be able to lock the "flywheel" with a pry bar to get the crank bolt properly tightened - may have to remove starter or could use a dust shield - dunno for sure on that one but that's a way to do it,

T

re-tired
Veteran / Moderator
re-tired profile image

Jan 17, 2010, 12:33 AM

Post #3 of 4 (2164 views)

Re: Crankshaft pully bolt	Sign In

I confess .In the v8 days a burp with the airgun worked , never had a failure . However , when the eng's got knocked sideways there was'nt room for the gun and/or the torque value was lower than i could get gun adjusted to. This is a way when you dont have access to flywheel like this one.Remove #1 plug, turn eng to TDC #1 cyl. Take a length of 1/8 inch dia cotton clothes line . turn eng slightly either before or after TDC depending on crankbolt being LH or RH thread. Feed in lne till cyl is full. Carefully torque bolt .Back eng up to relieve pressure . Take out line.

LIFE'S SHORT GO FISH

nickwarner
Veteran / Moderator
nickwarner profile image

Jan 18, 2010, 10:43 PM

Post #4 of 4 (2151 views)

Re: Crankshaft pully bolt	Sign In

Matco tools has a tool for this purpose that I believe is called the crankstopper. It threads into the spark plug hole and stops the piston from continuing in its travel. remember to take the thing out before you try to start the motor. Sounds dumb, but I've seen in happen when people get distracted. I don't think it costs too much for it.

Search for (options) Privacy Sitemap