|
|
|
1951 chevy 3600 pickup rearend replacement
|
|
|
| |
|
|
snalley78
New User
Aug 11, 2011, 5:30 PM
Post #1 of 6
(11214 views)
|
|
1951 chevy 3600 pickup rearend replacement
|
Sign In
|
|
I NEED HELP CHOOSING A REAREND FOR MY 1951 CHEVY 3600 PICKUP. IM BUILDING A DRIVER AND PUTTING A 350 IN IT. I NEED TO KNOW WHAT WOULD BE A GOOD FIT FOR IT. ID LIKE SOMETHING WITH 373 GEARS POSSIBLY OR SOMETHING CLOSE, BUT I DONT KNOW IF I SHOULD BE LOOKING FOR A CAMARO, NOVA, CAPRICE REAREND OR WHAT? I JUST DONT KNOW WHAT WOULD BE THE BEST FIT UNDER THE TRUCK WITHOUT ALOT OF MODIFICATIONS. I WANNA TO KEEP THE CHEVY BOLT PATTERN 5- 4 3/4. ANY ADVICE OR HELP WOULD BE GREAT, THANKS
|
|
| |
|
|
re-tired
Veteran
/ Moderator
Aug 11, 2011, 8:03 PM
Post #2 of 6
(11188 views)
|
|
Re: 1951 chevy 3600 pickup rearend replacement
|
Sign In
|
|
They dont make a 3600 truck . im sure you meant 3500. Why would you want to put a car axle under a 1 ton truck ? Hit the salvage yards with the measurements from your existing axle ,such a total width , spring platforms etc It may be hard to find a used 3500 axle . They go fast.
LIFE'S SHORT GO FISH
|
|
| |
|
|
snalley78
New User
Aug 13, 2011, 7:18 AM
Post #3 of 6
(11173 views)
|
|
Re: 1951 chevy 3600 pickup rearend replacement
|
Sign In
|
|
THEY DO MAKE A 1951 3600 CHEVY PICKUP, I HAVE ONE IN MY GARAGE. ITS A 3/4 TON. BUT YOUR TELLING ME I SHOULD GET ALL MY MEASUREMENTS, AND HIT THE JUNK YARDS? I CAN DO THAT. THANKS
|
|
| |
|
|
re-tired
Veteran
/ Moderator
Aug 13, 2011, 2:27 PM
Post #4 of 6
(11159 views)
|
|
Re: 1951 chevy 3600 pickup rearend replacement
|
Sign In
|
|
Of course your right . I had late model on the brain .My apoligies. I still would think twice about puttting a passenger car axle under irt . Find a late model 3/4 ton axle . It should be more available than the 1ton . To set things right ,here is a tip I ran aross .
heres your tip; home about us parts catalog ask jim showcase support Discussion Forum contact us 1947-1954 Rear Spring Alignment Tech Tip from Ron Hansen
Wakefield, Massachusetts
Alignment Solution for Installing a Late Model Rear End in a 1947-1954 Pick Up
On the original rear end, the spring centerbolt is offset to the front of the spring by 2″to 3″. If you install a modern rear end (with an open driveshaft) and retain the original springs, the wheels will end up offset forward (inside) of the original wheel openings in the fenders. To correct this problem, remove the original springs and reverse them end to end (front to back) as they are the same on both ends. This will bring the spring centerbolt to the rear of the axle and place the new rear end in the center of the fender wheel openings.
Click to enlarge
Tags: 1947, 1954, old chevy truck, rear spring alignment
LIFE'S SHORT GO FISH
|
|
| |
|
|
joes51
New User
Sep 10, 2011, 9:30 PM
Post #5 of 6
(11110 views)
|
|
Re: 1951 chevy 3600 pickup rearend replacement
|
Sign In
|
|
Hello, I have a 3600 driver and wanted to know if you figured out the rear end problem. As you know, the gearing is not good for the highway speeds of today. Mine wines bad at 55 or so with the engine rpm really up there. I want to find a different gear ratio instead of changing it out. Any info would be appreciated. Thanks
|
|
| |
|
|
zmame
Veteran
/ Moderator
Sep 11, 2011, 11:46 AM
Post #6 of 6
(11089 views)
|
|
Re: 1951 chevy 3600 pickup rearend replacement
|
Sign In
|
|
If you have a question please start a new thread.
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
1989 toyota pickup 3.0 crank no start
Please Help - Knock sound & engine fail
Blog this!