Bleeding clutch system_HELP!! - Truck Repair Advice


	Auto Repair Home	SEARCH POSTS	WHO'S ONLINE	LOG IN

Automotive Repair

Car Troubleshooting Topics
  Car Troubleshooting
  Engine Troubleshooting
  Engine Fault Codes
  Electrical and Wiring
  Transmission Problems

Car Repair Topics
  Car Making Noises
  Car Stereo Repair
  Heating or AC Issues
  Motorcycles and ATVs
  Tricks of the Trade
  Truck Repair Advice

Site Options:
  Login
  Sign up here!

Latest Forum Post

1989 toyota pickup 3.0 crank no start

I have a 1989 toyota pickup 3.0 crank no...

Strut spring orientation and strut mount tension nut

2017 Nissan rogue awd 2.5 L Put in Monro...

Transmission stuck in part, I have tried everything

So I'm working on my elderly fathers 201...

2017 dodge journey LED headlights on/off randomly

Year of vehicle 2017 Make of vehicle dod...

Kia Soul starter replacement issues!

Okay so my car is a 2010 Kia soul 2.0 en...

Please Help - Knock sound & engine fail

Hi all, Hoping to get some insight and ...

multiple warning lights

2013 GMC Terrain 130,000 miles 4 cylinde...

03 alero no low speed blower

Good day everyone, I have a 2003 Olds a...

04 Chevy 2500hd tail light issues

Help!!! I have changed my combo switch...

1999 Grand Caravan Sport not starting.

Hi. I'm new here. I hope someone can hel...

Bleeding clutch system_HELP!!

Sign up here!

Search for (search options)

Auto Repair Home>> Truck Repair>> Truck Repair Advice

we3861
New User

Nov 9, 2008, 4:23 AM

Post #1 of 4 (2885 views)

Bleeding clutch system_HELP!!	Sign In

2003 Mazda B3000 4.9 ,clutch went to the floor with zero pressure but returned to top normally, replaced slave cyli nder {without pre-filling},bled system many times and now have some pressure but still won't go in gear except when not running.Also spring on new slave about an inch taller than old one but I used it. Any bleeding tips???

(This post was edited by we3861 on Nov 9, 2008, 9:07 AM)

Loren Champlain Sr
Veteran / Moderator
Loren Champlain Sr profile image

Nov 9, 2008, 1:34 PM

Post #2 of 4 (2857 views)

Re: Bleeding clutch system_HELP!!	Sign In

Be certain that the master cylinder is completely bled of air. Note where the bleeder is located on the slave. I've had to remove the slave and hold it so that the bleeder is higher than the slave while gravity bleeding. I'm not sure what spring you were referring to?
Loren
SW Washington

we3861
New User

Nov 9, 2008, 3:40 PM

Post #3 of 4 (2848 views)

Re: Bleeding clutch system_HELP!!	Sign In

Thanks for your response!The spring wraps around the plastic cylinder shaped part and is covered by a rubber boot.I actually drove truck today but not going in gear as easy as before with reverse being the worst and not the pedal resistance as before.The SPRING has one more full coil than the old one which made using the old boot difficult. Bled system twice more today.

Jeff Norfolk
Enthusiast
Jeff Norfolk profile image

Nov 9, 2008, 5:25 PM

Post #4 of 4 (2842 views)

Re: Bleeding clutch system_HELP!!	Sign In

Just to add to the good advice from above. If this system lost all or most of the fluid than the master cylinder has air in it too. These set ups are problematic about air in the master cylinder. You will need to remove it a bleed it on the bench. Here is what to do. Hold the reservoir above the rest of the master cylinder. I usually clam it in a vise. Then hold the master cylinder with the push rod that atatches to the clutch pedal pointed to the floor. Now at the end of the line that connects to the slave cylinder gently push the center of it in until fluid runs out. Do this several times without letting the reservoir run dry. This is always needed and dose the trick for me. Good Luck
Jeff

Search for (options) Privacy Sitemap