Latest Forum Post
04 Chevy 2500hd tail light issues
Help!!! I have changed my combo switch...
1999 Grand Caravan Sport not starting.
Hi. I'm new here. I hope someone can hel...
Brake Seals Bulging
2021 Toyota Corolla LE 1.8l 65,000 mile...
Engine blew up after oil change, is mechanic responsible?
Hello, I have a 2007 Hyundai Elantra wit...
Changed pads and now brake pedel goes to the floor
I am not much of a mechanic, and needed ...
Equinox air conditioning issue, help please!
I have a 2020 Chevrolet Equinox that has...
2005 Maxima overheats only when idling but engine temp comes down immediately if I rev up the engine (even though car is stationary)
hello everyone, I own a 2005 Nissan M...
Brake & Turn Signal Out - One side only
2002 Ford Ranger 3.0 V6, 5-speed manual ...
Seeking Advice: Strange Noise in 2017 Nissan Versa Note, Mechanic Stumped
Hey everyone, A few weeks ago, my mom's...
Replacing Tires
My daughter just purchased a 2013 Honda ...
|
|
|
Rear bearing replacement chevy silverado 3500
|
|
|
| |
|
|
Ryan77
Novice
Sep 24, 2016, 3:41 PM
Post #1 of 12
(3692 views)
|
|
Rear bearing replacement chevy silverado 3500
|
Sign In
|
|
Chevy silverado 3500.... need help with how the new bearings and races go in..do I hammer the outer race in over the bearing or do I put the race in then the bearing and rely on thr split ring to hold the bearing in
(This post was edited by Ryan77 on Sep 24, 2016, 3:52 PM)
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Sep 24, 2016, 4:00 PM
Post #2 of 12
(3671 views)
|
|
Re: Rear bearing replacement chevy silverado 3500
|
Sign In
|
|
Which bearings and races are you replacing?
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
|
Ryan77
Novice
Sep 24, 2016, 4:00 PM
Post #3 of 12
(3669 views)
|
|
Re: Rear bearing replacement chevy silverado 3500
|
Sign In
|
|
Inner and outer rear wheel
|
|
| |
|
|
Ryan77
Novice
Sep 24, 2016, 4:01 PM
Post #4 of 12
(3668 views)
|
|
Re: Rear bearing replacement chevy silverado 3500
|
Sign In
|
|
Inner and outer rear wheel
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Sep 24, 2016, 4:04 PM
Post #5 of 12
(3663 views)
|
|
Re: Rear bearing replacement chevy silverado 3500
|
Sign In
|
|
Which year? This is full floating rear axle right?
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
|
Ryan77
Novice
Sep 24, 2016, 4:05 PM
Post #6 of 12
(3661 views)
|
|
Re: Rear bearing replacement chevy silverado 3500
|
Sign In
|
|
2001 chevy silverado 3500 2wh drive gas engine and I believe it is a full floating
(This post was edited by Ryan77 on Sep 24, 2016, 4:08 PM)
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Sep 24, 2016, 4:13 PM
Post #7 of 12
(3649 views)
|
|
Re: Rear bearing replacement chevy silverado 3500
|
Sign In
|
|
1. Lubricate the following with a light coat of high melting point Extreme Pressure bearing lubricant:
^ The outer wheel bearing
^ The inner wheel bearing
^ The outer wheel bearing cup
^ The inner wheel bearing cup
^ The axle housing
2. Install the outer bearing into the wheel hub.
3. Install the outer bearing cup into the wheel hub.
4. Drive the bearing cup into the wheel hub using the J 44419 (2) and the J 8092 (1).
5. Install the retaining ring into the groove. Make sure the retaining ring is fully and evenly seated in the groove.
6. Install the inner bearing cup.
7. Drive the inner bearing cup into the wheel hub using the J 24427 (2) and the J 8092 (1).
8. Install the inner bearing.
Important: Each time you replace the wheel hub bearings, install a new oil seal in order to prevent the wheel hub from leaking.
9. Install the new oil seal using the J 44420 (2) and the J 8092 (1).
10. Install the hub and rotor assembly.
11. Install the tire and wheel assembly.
12. Inspect and add axle lubricant to the axle housing, if necessary.
13. Lower the vehicle.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
|
Ryan77
Novice
Sep 24, 2016, 4:16 PM
Post #8 of 12
(3647 views)
|
|
Re: Rear bearing replacement chevy silverado 3500
|
Sign In
|
|
So I hammer the cup in over thr bearing? And the retaining ring holds the cup in?
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Sep 24, 2016, 4:17 PM
Post #9 of 12
(3645 views)
|
|
Re: Rear bearing replacement chevy silverado 3500
|
Sign In
|
|
According to service information, yes.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
|
Ryan77
Novice
Sep 24, 2016, 4:20 PM
Post #10 of 12
(3642 views)
|
|
Re: Rear bearing replacement chevy silverado 3500
|
Sign In
|
|
Thanks dude...I'm a carpenter by trade and can't find a good video or instructions anyplace
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Sep 24, 2016, 4:24 PM
Post #11 of 12
(3637 views)
|
|
Re: Rear bearing replacement chevy silverado 3500
|
Sign In
|
|
Since you're a carpenter, you should be good at hammering the cups in. Just make sure you wear eye protection. Let us know how it turns out, so this thread can be resolved.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Sep 24, 2016, 4:24 PM)
|
|
| |
|
|
Ryan77
Novice
Sep 24, 2016, 4:27 PM
Post #12 of 12
(3632 views)
|
|
Re: Rear bearing replacement chevy silverado 3500
|
Sign In
|
|
I've never done anything like this b4...do I just post my end result here like this?
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
