00' tacoma lower ball joints - Car Troubleshooting


	Auto Repair Home	SEARCH POSTS	WHO'S ONLINE	LOG IN

Automotive Repair

Car Troubleshooting Topics
  Car Troubleshooting
  Engine Troubleshooting
  Engine Fault Codes
  Electrical and Wiring
  Transmission Problems

Car Repair Topics
  Car Making Noises
  Car Stereo Repair
  Heating or AC Issues
  Motorcycles and ATVs
  Tricks of the Trade
  Truck Repair Advice

Site Options:
  Login
  Sign up here!

Latest Forum Post

Carbon Fiber parts/concern

Im a bit of a hypochondriac so when I sa...

Battery woes 2010 Ranger 4.0

This vehicle is not a daily driver , I s...

This isn't normal, right?

Gap between connections on exhaust. I be...

Lukewarm Heat............

New antifreeze reverse flush heater core...

multiple warning lights

2013 GMC Terrain 130,000 miles 4 cylinde...

2014 Nissan Sentra Shaking

Car recently started shaking when accele...

Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086

N/A

1989 toyota pickup 3.0 crank no start

I have a 1989 toyota pickup 3.0 crank no...

Strut spring orientation and strut mount tension nut

2017 Nissan rogue awd 2.5 L Put in Monro...

Transmission stuck in part, I have tried everything

So I'm working on my elderly fathers 201...

00' tacoma lower ball joints

Sign up here!

Search for (search options)

Auto Repair Home>> Automotive Repair>> Car Troubleshooting

samg.
User
samg. profile image

Oct 7, 2011, 6:21 PM

Post #1 of 3 (2281 views)

00' tacoma lower ball joints	Sign In

Sorry to ask but GM tech working on toyota here!

A buddy of mine wants his lower ball joints and f shocks replaced, ive put them in on yukons, sierras so on but never a toyota. They look like they come bolted in from the factory so is it just a simple as poppin the tie rod end and joint out of knuckle then unbolting and beating that mother til it comes out?

I would assume if they bolt in no press will be needed?

Discretesignals
Ultimate Carjunky / Moderator
Discretesignals profile image

Oct 7, 2011, 6:33 PM

Post #2 of 3 (2266 views)

Re: 00' tacoma lower ball joints	Sign In

Yep, disconnect the outer tie rod from the knuckle. Loosen the four nuts and remove the castle nut. Hammer shock or use a ball joint shafter remover ( gear puller) to pop the shaft out of the lower control arm. Take the four bolts out and lift up on the knuckle and upper control arm and remove the joint.

You don't have to remove the CV or disassemble the brakes. 4 bolts get tightened to 59 ft/lbs and the castle nut to 103 ft/lbs. If the hole doesn't line up for the cotter pin, tighten the nut a little more to line up the hole. Tie rod nut gets 67 ft/lbs.

You'll need a strut compressor to R and R the shock in the front. Removing the shock assembly is pretty self explanatory and will be easier to do with lower ball joint removed. Make sure you mark everything before taking the shock/spring assembly apart.

The large shock nut and bolt get 101 ft/lbs. The three upper mount nuts get 47 ft/lbs and the shock top nut get 22 ft/lbs.

You'll find that working on Toyota is really easy and everything fits really nice and is well designed.

Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.

(This post was edited by Discretesignals on Oct 7, 2011, 6:50 PM)

samg.
User
samg. profile image

Oct 7, 2011, 9:12 PM

Post #3 of 3 (2242 views)

Re: 00' tacoma lower ball joints	Sign In

Thank you.

Search for (options) Privacy Sitemap