Main IndexAuto Repair Home Search Posts SEARCH
POSTS 		Who's Online WHO'S
ONLINE 		Log in LOG
IN




Automotive Repair
Car Troubleshooting Topics
  Car Troubleshooting
  Engine Troubleshooting
  Engine Fault Codes
  Electrical and Wiring
  Transmission Problems

Car Repair Topics
  Car Making Noises
  Car Stereo Repair
  Heating or AC Issues
  Motorcycles and ATVs
  Tricks of the Trade
  Truck Repair Advice

Site Options:   
  Login
  Sign up here!



Latest Forum Post
with_replies.gif image   Carbon Fiber parts/concern
Im a bit of a hypochondriac so when I sa...

with_replies.gif image   Battery woes 2010 Ranger 4.0
This vehicle is not a daily driver , I s...

hot_with_replies.gif image   This isn't normal, right?
Gap between connections on exhaust. I be...

with_replies.gif image   Lukewarm Heat............
New antifreeze reverse flush heater core...

with_replies.gif image   multiple warning lights
2013 GMC Terrain 130,000 miles 4 cylinde...

with_replies.gif image   2014 Nissan Sentra Shaking
Car recently started shaking when accele...

no_replies.gif image   Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086
N/A

hot_with_replies.gif image   1989 toyota pickup 3.0 crank no start
I have a 1989 toyota pickup 3.0 crank no...

with_replies.gif image   Strut spring orientation and strut mount tension nut
2017 Nissan rogue awd 2.5 L Put in Monro...

with_replies.gif image   Transmission stuck in part, I have tried everything
So I'm working on my elderly fathers 201...




drive axle

Search for (search options)
 



greasemonkey29
New User

Oct 9, 2011, 9:26 AM

Post #1 of 4 (1760 views)
drive axle Sign In
on a 1994 toyota camry xle V6 how does one separate the right side drive axle from the intermediate shaft? Currently both are removed from vehicle as one piece.


Discretesignals
Ultimate Carjunky / Moderator
Discretesignals profile image

Oct 9, 2011, 11:23 AM

Post #2 of 4 (1727 views)
Re: drive axle Sign In
I don't think that they come apart unless you take the inboard CV joint apart. I believe it is part of the housing. When you buy a reman axle it comes with the intermediate shaft and CV all as one. The later years the shafts would come apart.





Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.


greasemonkey29
New User

Oct 9, 2011, 11:50 AM

Post #3 of 4 (1720 views)
Re: drive axle Sign In
yes they do come apart because I have already purchased a new drive axle and the intermediate shaft does not come with it


Discretesignals
Ultimate Carjunky / Moderator
Discretesignals profile image

Oct 9, 2011, 12:00 PM

Post #4 of 4 (1716 views)
Re: drive axle Sign In
Remove the bolts from the inboard cover. Smack the joint where the shaft covers together with a rubber mallet. Install shaft onto new CV axle and install bolts with washer hand tight. Install axle into vehicle. Tighten the six joint bolts to 49 ft/lbs after installing outboard CV into wheel hub bearing and lower ball joint into lower control arm while someone is holding the brake.

Tighten bearing pinch bolt to 24 ft/lbs.
Lower control arm bolt and nuts to 94 ft/lbs
Tighten CV axle nut to 217 ft/lbs
Stabilizer link nuts 29 ft/lbs
Tie rod end castle nut 36 ft/lbs. Note: Do not loosen to line up cotter pin hole.

Hint: Tighten the axle nut with the wheel installed and on the ground.

Make sure that you top off the transaxle fluid if any was lost.

Have a nice day





Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.

(This post was edited by Discretesignals on Oct 9, 2011, 12:27 PM)





 
 
 






Search for (options) Privacy Sitemap