Main IndexAuto Repair Home Search Posts SEARCH
POSTS 		Who's Online WHO'S
ONLINE 		Log in LOG
IN




Automotive Repair
Car Troubleshooting Topics
  Car Troubleshooting
  Engine Troubleshooting
  Engine Fault Codes
  Electrical and Wiring
  Transmission Problems

Car Repair Topics
  Car Making Noises
  Car Stereo Repair
  Heating or AC Issues
  Motorcycles and ATVs
  Tricks of the Trade
  Truck Repair Advice

Site Options:   
  Login
  Sign up here!



Latest Forum Post
with_replies.gif image   Carbon Fiber parts/concern
Im a bit of a hypochondriac so when I sa...

with_replies.gif image   Battery woes 2010 Ranger 4.0
This vehicle is not a daily driver , I s...

hot_with_replies.gif image   This isn't normal, right?
Gap between connections on exhaust. I be...

with_replies.gif image   Lukewarm Heat............
New antifreeze reverse flush heater core...

with_replies.gif image   multiple warning lights
2013 GMC Terrain 130,000 miles 4 cylinde...

with_replies.gif image   2014 Nissan Sentra Shaking
Car recently started shaking when accele...

no_replies.gif image   Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086
N/A

hot_with_replies.gif image   1989 toyota pickup 3.0 crank no start
I have a 1989 toyota pickup 3.0 crank no...

with_replies.gif image   Strut spring orientation and strut mount tension nut
2017 Nissan rogue awd 2.5 L Put in Monro...

with_replies.gif image   Transmission stuck in part, I have tried everything
So I'm working on my elderly fathers 201...




hazard flashers

Search for (search options)
 



Guest
Anonymous Poster

Jan 22, 2009, 1:46 PM

Post #1 of 6 (2691 views)
hazard flashers Sign In
2003 chevy express 3500 6.0

when I put my hazard flashers on sometimes they work sometimes they dont. I can get them to work if I put a blinker on, then the hazard lights on next they will work. I dont think the van has a flasher but some kind of module. If some one can tell me exactly what it is called and where it is located on the car would be appreciated.


DrElectrics
Enthusiast
DrElectrics profile image

Jan 22, 2009, 1:49 PM

Post #2 of 6 (2689 views)
post icon Re: hazard flashers Sign In
Flasher cans and module should will be under the hood in your fuse box. Take the lid off the box and find on the lid it will give you the run down of what everything is.


Double J
Veteran / Moderator
Double J profile image

Jan 22, 2009, 1:54 PM

Post #3 of 6 (2688 views)
Re: hazard flashers Sign In
HAZARD AND TURN SIGNAL FLASHER REPLACEMENT

REMOVAL PROCEDURE


  1. Remove the left knee bolster bracket.
  2. Remove the turn / hazard flasher (2) from the Instrument Panel (I/P) Support.
  3. Disconnect the electrical connector (1).
  4. Remove the turn / hazard flasher (2).


Another possibility could be the Turn signal/multifunction switch.





(This post was edited by JIM N on Jan 22, 2009, 1:59 PM)


Guest
Anonymous Poster

Jan 22, 2009, 2:08 PM

Post #4 of 6 (2683 views)
Re: hazard flashers Sign In
jim,

forgive my ignorance but where is the left knee bolster bracket


Double J
Veteran / Moderator
Double J profile image

Jan 22, 2009, 2:13 PM

Post #5 of 6 (2681 views)
Re: hazard flashers Sign In
The knee bolster is the lower panel that mounts to the instrument panel about at the level of the knee.

Here is a pic...hope it helps...


  1. Remove the bolts (2) from the lower edge of the instrument panel (I/P) driver knee bolster panel (1).
  2. Pull the I/P driver knee bolster panel (1) towards the rear of the vehicle in order to disengage the retainers.
  3. Remove the I/P driver knee bolster panel (1) from the vehicle.
  4. Inspect the I/P driver knee bolster panel (1) for broken or missing retainers. Replace the retainers as needed.


Guest
Anonymous Poster

Jan 22, 2009, 4:31 PM

Post #6 of 6 (2675 views)
Re: hazard flashers Sign In
jim thanks for the detailed reply greatly appreciated





 
 
 






Search for (options) Privacy Sitemap