Inadvertenually put water in oil - Car Troubleshooting


	Auto Repair Home	SEARCH POSTS	WHO'S ONLINE	LOG IN

Automotive Repair

Car Troubleshooting Topics
  Car Troubleshooting
  Engine Troubleshooting
  Engine Fault Codes
  Electrical and Wiring
  Transmission Problems

Car Repair Topics
  Car Making Noises
  Car Stereo Repair
  Heating or AC Issues
  Motorcycles and ATVs
  Tricks of the Trade
  Truck Repair Advice

Site Options:
  Login
  Sign up here!

Latest Forum Post

1989 toyota pickup 3.0 crank no start

I have a 1989 toyota pickup 3.0 crank no...

Strut spring orientation and strut mount tension nut

2017 Nissan rogue awd 2.5 L Put in Monro...

Transmission stuck in part, I have tried everything

So I'm working on my elderly fathers 201...

2017 dodge journey LED headlights on/off randomly

Year of vehicle 2017 Make of vehicle dod...

Kia Soul starter replacement issues!

Okay so my car is a 2010 Kia soul 2.0 en...

Please Help - Knock sound & engine fail

Hi all, Hoping to get some insight and ...

multiple warning lights

2013 GMC Terrain 130,000 miles 4 cylinde...

03 alero no low speed blower

Good day everyone, I have a 2003 Olds a...

04 Chevy 2500hd tail light issues

Help!!! I have changed my combo switch...

1999 Grand Caravan Sport not starting.

Hi. I'm new here. I hope someone can hel...

Inadvertenually put water in oil

Sign up here!

Search for (search options)

Auto Repair Home>> Automotive Repair>> Car Troubleshooting

Guest
Anonymous Poster
rudyblum@ix.netcom.com

Feb 1, 2009, 1:55 PM

Post #1 of 3 (2650 views)

Inadvertenually put water in oil	Sign In

inadvertenually put water in oil tank

(edited to change subject line 2-1-2009)

(This post was edited by Tom Greenleaf on Feb 1, 2009, 5:45 PM)

Loren Champlain Sr
Veteran / Moderator
Loren Champlain Sr profile image

Feb 1, 2009, 2:03 PM

Post #2 of 3 (2648 views)

Re: rudyblum	Sign In

Have you started the engine, yet? If not, just drain the oil pan. If you have already started it, drain the oil and leave the drain plug out for a couple of hours, replace the filter. After you've run it long enough to reach temperature, you can do it again, and should be okay. You can also buy some engine flush, but I don't really like using that stuff.
Loren
SW Washington

Tom Greenleaf
Ultimate Carjunky / Moderator
Tom Greenleaf profile image

Feb 1, 2009, 5:58 PM

Post #3 of 3 (2642 views)

Re: Inadvertenually put water in oil	Sign In

Loren - Readers:

Changed subject line of first post and this as it's a good subject. (FIRST SUBJECT LINE WAS JUST "rudyblum") I don't know exactly what happened by putting what in what oil tank that is mentioned first ---- oil for engine??

I'd do as Loren said if this went into engine oil fill. If it's been run it would likely mix up with oil and stay mixed. If water is put in a true oil and nothing touched it should go to the bottom quite nicely but I'd still change out that oil completely again and watch after a warm up.

Note: Engine, transmissions, gearcases, power steering use OIL products (near always) and should float on water. BRAKE FLUID is NOT an oil and will mix with water if DOT 4 or lower! Uncertain at this writing for DOT 5 requirements but suspect water would not mix and go to lowest spots. Either way a complete flush out if brake fluid is involved it suggested at once!

T

Search for (options) Privacy Sitemap