|
|
|
can't pass inspection. EVap not ready
|
|
|
| |
|
|
babkuzy
Novice
Aug 14, 2012, 4:46 PM
Post #1 of 10
(15135 views)
|
|
can't pass inspection. EVap not ready
|
Sign In
|
|
Check engine came up, got oxygen sensor replaced, drove around 40 miles, evap isn't ready along with issue with catalytic con. Mechanic said, let engine cool off for 8 hours, idle for 2 mintues and drive around 50mph for 20 minutes, did that still no good. Before that I drove the car for a good 200 miles but no particular drive cycle. Total mileage after initial repair is at least 400. Went on google today and found mazda 2003 drive cycle it says for EVAP to T2 (more than 15 minutes) and go 40-50 mph (V2) for 300 seconds and to idle for 200 seconds. Will try that tomorrow, but what exactly is T2 (more than 15 minutes)? just start car and wait 15 minutes (idle)? Any other advice you have for me? 10 day extension for inspection is over but no tickets yet.
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Aug 14, 2012, 4:55 PM
Post #2 of 10
(15121 views)
|
|
Re: can't pass inspection. EVap not ready
|
Sign In
|
|
Are there any codes being stored in the engine computer? pending codes?
Also would help to know the year, make, model, and engine size.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Aug 14, 2012, 5:00 PM)
|
|
| |
|
|
babkuzy
Novice
Aug 14, 2012, 4:59 PM
Post #3 of 10
(15117 views)
|
|
Re: can't pass inspection. EVap not ready
|
Sign In
|
|
Sorry, new to this so will try to explain from what I understand. I was probably scanned 10 times after getting Oxygen sensor replaced, all the 10 times mechanic said you still have 2 codes left, you need to clear one of them. One is EVAP , the other with catalytic converter but both codes are not ready so it will only say its "not ready"... mechanic said that most likely u have a faulty catalytic con so if it code shows up your engine will light up again but if EVAP passes, you are good to go anyway but EVAP wont pass. need to drive more. Hopefully this clears it up
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Aug 14, 2012, 5:03 PM
Post #4 of 10
(15102 views)
|
|
Re: can't pass inspection. EVap not ready
|
Sign In
|
|
Year, make, model, and engine size. What are the code numbers that are popping up?
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Aug 14, 2012, 5:04 PM)
|
|
| |
|
|
babkuzy
Novice
Aug 14, 2012, 5:05 PM
Post #5 of 10
(15097 views)
|
|
Re: can't pass inspection. EVap not ready
|
Sign In
|
|
2003 mazda mpv , not sure of engine type
|
|
| |
|
|
babkuzy
Novice
Aug 14, 2012, 5:06 PM
Post #6 of 10
(15094 views)
|
|
Re: can't pass inspection. EVap not ready
|
Sign In
|
|
code numbers are not popping out because its not ready yet, needs to be driven more.
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Aug 14, 2012, 5:12 PM
Post #7 of 10
(15090 views)
|
|
Re: can't pass inspection. EVap not ready
|
Sign In
|
|
3.0L
If you have code(s) pending or current, depending on the code(s) some monitors won't ready. For example: You have an O2 sensor code popping up. The catalyst monitor won't run because it uses the O2 sensors to test the catalyst. There are certain prerequisites that have to be achieved for certain monitors to ready and run.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
|
|
| |
|
|
babkuzy
Novice
Aug 14, 2012, 5:15 PM
Post #8 of 10
(15088 views)
|
|
Re: can't pass inspection. EVap not ready
|
Sign In
|
|
Yeah I will try doing a drive cycle tomorrow that I found online. Would you be able to look at my question about what T2 means in terms of the drive cycle itself.
Thanks
|
|
| |
|
|
babkuzy
Novice
Aug 14, 2012, 5:15 PM
Post #9 of 10
(15087 views)
|
|
Re: can't pass inspection. EVap not ready
|
Sign In
|
|
if you go here, i attached a picture to a post to reference to the t2 part
link deleted , not allowed
(This post was edited by Hammer Time on Aug 14, 2012, 5:26 PM)
|
|
| |
|
|
Discretesignals
Ultimate Carjunky
/ Moderator
Aug 14, 2012, 6:38 PM
Post #10 of 10
(15061 views)
|
|
Re: can't pass inspection. EVap not ready
|
Sign In
|
|
Well, your missing part of the information that describes what T and V are for.
Read this:
http://forum.mpvclub.com/...2623b76345a40dde82d6
The only problem I see is that the drive chart doesn't match what I am showing in service information, but you could try that to see if it works for you. Notice that there has to be criteria met and there can't be any trouble codes stored or else the monitors won't ready.
Just so you know. FTL is fuel tank level.
Since we volunteer our time and knowledge, we ask for you to please follow up when a problem is resolved.
(This post was edited by Discretesignals on Aug 14, 2012, 6:42 PM)
|
|
| |
|
Auto Repair Home
SEARCH
WHO'S 
LOG 
Lukewarm Heat............
Buy Flualprazolam Powder Online Whatsapp: +1(424) 328-1086
1989 toyota pickup 3.0 crank no start
